2015-12-17
Today I managed to fabricate the Trim Bellcrank Brackets and the Trim Cable Anchor Brackets from the aluminium angle provided in the kit. After that all parts incl. the Trim Mount Bracket have been primed and assembled. The elevator trim servo (Ray Allen type) was installed and tested on the trim mount bracket.
Finished product:
2015-12-17
Today the upper skin was riveted to the tailcone structure; first half of the skin was accessible from the outside, for the remaining rivets I had to crawl inside of the tailcone which proved to be comfy as long as you are laying on some of pillows. You could even take a nap inside 
The battery rack incl. the Elevator Bellcrank & the Elevator Pushrod have been bolted as well. The Elevator Pushrod was primed with a 2K Epoxy Primer – smells like hell but gives a good finish.. I plan to use the 2K Primer on all pushrods.
Inside of the tailcone, ready to go with the bucking bars. Some paint had to be repaired as well:
| KIT | Section | Page complete / memo | Date | Hours | Completed | Verified | CAA entry / memo |
|---|---|---|---|---|---|---|---|
| 2576.4 | TOTAL Project Hours | ||||||
| 2138.9 | TOTAL Project Hours | ||||||
| EMPENNAGE | Unboxing / Inventory | 04/12/2015 | 8.5 | Halanda | |||
| EMPENNAGE | 6 Vertical Stabilizer | 6-2 -> 6-3 (incl. dimpling, deburring and test assy) | 05/12/2015 | 6.5 | Halanda | Benedikovic | |
| EMPENNAGE | 6 Vertical Stabilizer | 6-4 -> 6-5 (incl. priming) | 06/12/2015 | 7.2 | Halanda | Benedikovic | |
| EMPENNAGE | 6 Vertical Stabilizer | 6-5 | 07/12/2015 | 8.5 | Halanda | Benedikovic | |
| EMPENNAGE | 6 Vertical Stabilizer | 6-5 -> 6-6 finished | 08/12/2015 | 7.5 | Halanda | Benedikovic | |
| EMPENNAGE | 10 Tailcone | 10.2 -> 10.4 general alignment of parts, deburring, priming | 08/12/2015 | 2.5 | Halanda | Benedikovic | |
| EMPENNAGE | 10 Tailcone | 10.3 -> 10.5 bulkhead assembly-riveting | 09/12/2015 | 9 | Halanda | Benedikovic | |
| EMPENNAGE | 10 Tailcone | 10.7 -> 10.9 priming & riveting | 10/12/2015 | 9.5 | Halanda | Benedikovic | |
| EMPENNAGE | 10 Tailcone | 10.7 Riveting the side-walls to stringers & bulkheads | 11/12/2015 | 6.7 | Halanda | Benedikovic | |
| EMPENNAGE | 10 Tailcone | 10.0 -> 10.11 Deburring, Priming and Riveting the AFT Deck | 12/12/2015 | 4.5 | Halanda | Benedikovic | |
| EMPENNAGE | 10 Tailcone | Test-Fitting the upper skins | 13/12/2015 | 1 | Halanda | Benedikovic | |
| TOOLS | 15/12/2015 | 0.5 | Halanda | Replaced compressor, oil change & filter cleaned | |||
 | 15/12/2015 Inspected by The Transport Authority of Slovak Republic | ||||||
| EMPENNAGE | 10 Tailcone | 10.12 -> 10.26 Bolting the shoulder harness Anchores, Attaching the battery mount, bolting the elev. bellcrank, riveting the upper skin | 17/12/2015 | 8 | Halanda | Benedikovic | |
| EMPENNAGE | 11 Empennage Attach | 11.6, 11.8 -> 11.9 Assembling & priming the elev. pushrod, manufacturing & priming of the elev. trim parts | 17/12/2015 | 2.3 | Halanda | Benedikovic | |
| EMPENNAGE | 7 Rudder | 7.2 -> 7.3 Started works on the Rudder. Ribs, Stiffeners & Shear clips separated, deburred & primed. | 20/12/2015 | 3.5 | Halanda | Benedikovic | |
| EMPENNAGE | 7 Rudder | 7.4 -> 7.6 | 21/12/2015 | 5 | Halanda | Benedikovic | |
| EMPENNAGE | 7 Rudder | 7.6 -> 7.8 | 22/12/2015 | 6.5 | Halanda | Benedikovic | |
| EMPENNAGE | 7 Rudder | 7.9 -> 7.10 | 27/12/2015 | 8 | Halanda | Benedikovic | |
| EMPENNAGE | 7 Rudder | 7.11 -> 7.12 Rudder finished. Added counterweights, skins bended. | 28/12/2015 | 9 | Halanda | Benedikovic | |
| EMPENNAGE | 12 Empennage Fairings | 12.2 -> 12.3 Rudder Fairings -finished | 28/12/2015 | 1.5 | Halanda | Benedikovic | |
| EMPENNAGE | 8 Horizontal Stabilizer | 8.2 -> 8.7 | 1/1/2016 | 9.5 | Halanda | Benedikovic | |
| EMPENNAGE | 8 Horizontal Stabilizer | 8.8 Testfitting | 3/1/2016 | 4.5 | Halanda | Benedikovic | |
| EMPENNAGE | 8 Horizontal Stabilizer | 8.8 -> 8.10 Dimpling, Deburring and Priming | 4/1/2016 | 7 | Halanda | Benedikovic | |
| EMPENNAGE | 8 Horizontal Stabilizer | 8.11 -> 8.12 Riveting the front spars to the skin and inspar ribs to the front spar assy | 5/1/2016 | 5.5 | Halanda | Benedikovic | |
| EMPENNAGE | 8 Horizontal Stabilizer | 8.11 -> 8.13 Riveting.. | 6/1/2016 | 8.5 | Halanda | Benedikovic | |
| EMPENNAGE | 8 Horizontal Stabilizer | 8.11 -> 8.13 Riveting.. | 7/1/2016 | 5.2 | Halanda | Benedikovic | |
| EMPENNAGE | 8 Horizontal Stabilizer | ..8.14 FINISHED | 8/1/2016 | 6.5 | Halanda | Benedikovic | |
| Enhancements | LNDG Lights | Install KIT received, examined and inventored | 9/1/2016 | 0.5 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | 9-2, 9-5 Separating Elevator Ribs, drilling, separating Shear Clips.. | 10/1/2016 | 6 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | 9-2 -> 9-5 Deburring, dimpling, priming. Riveting of the half ribs & rear spar. | 11/1/2016 | 7.5 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | 9-5 -> 9-6 | 13/1/2016 | 8.5 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | 9-6 -> 9-10 | 14/1/2016 | 5 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | 9-10 -> 9-13 | 17/1/2016 | 7 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | 9-13 -> 9-15 | 18/1/2016 | 5 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | 2nd Elevaror: 9-2, 9-5 Separating Elevator Ribs, drilling, separating Shear Clips.. | 19/1/2016 | 8 | Halanda | Benedikovic | |
| EMPENNAGE | 9 Elevators | Trim Tabs attached | 14/3/2016 | 7.5 | Halanda | Benedikovic | |
| WINGS | Unboxing / Inventory | 15/3/2016 | 9.5 | Halanda | |||
| WINGS | Unboxing / Inventory | 17/3/2016 | 5.3 | Halanda | |||
| EMPENNAGE | 9 Elevators | 9-18 -> 9-19 Trim Tab Hinge (Elevators Finished) | 18/3/2016 | 3.5 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | Test assembly | 19/3/2016 | 8.6 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-2 -> 18-4 Dimpling, deburring, countersinking (general preparation of L tank for sealing | 20/3/2016 | 7.8 | Halanda | Benedikovic | |
| TOOLS | 20/3/2016 | Halanda | Angle Grinder added to tools/equipment | ||||
| WINGS | 18 Fuel Tank | 18-2 -> 18-4 | 23/3/2016 | 6.7 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-2 -> 18-5 | 24/3/2016 | 7 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-2 -> 18-5 | 25/3/2016 | 8 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-2 -> 18-5 | 27/3/2016 | 6 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-2 -> 18-5 | 29/3/2016 | 7.5 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-2 -> 18-5 Sealing Ribs; let it dry for almost 2 days | 03/4/2016 | 6.3 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-2 -> 18-5 Riveting ribs in the fuel tank | 05/4/2016 | 9 | Halanda | Benedikovic | |
| WINGS | 21 Aileron | 21-2 | 07/4/2016 | 8 | Halanda | Benedikovic | |
| WINGS | 21 Aileron | 21-2->21-4 | 08/4/2016 | 8.5 | Halanda | Benedikovic | |
| WINGS | 21 Aileron | 21-2->21-4 | 09/4/2016 | 7.3 | Halanda | Benedikovic | |
 | 12/05/2016 Inspected by The Transport Authority of Slovak Republic | ||||||
| WINGS | 21 Aileron | 21-5->21-9 | 12/5/2016 | 9.6 | Halanda | Benedikovic | |
| WINGS | 21 Aileron | 21-5->21-9 Ailerons finished | 14/5/2016 | 8 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 1st leak test | 18/5/2016 | 3.5 | Halanda | Benedikovic | 1st leak test with colored water successful! Both fuel tanks passed. |
| WINGS | 18 Fuel Tank | 18-4, 18-6 -> 18-8 Rear wall closed / sealed & clecoed | 19/5/2016 | 5.6 | Halanda | Benedikovic | |
| WINGS | 22 Flap | 22-2 -> 22-4 Deburred edges, ribs trimmed | 20/5/2016 | 7.5 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | 18-4, 18-6 -> 18-8 Rear wall riveted | 21/5/2016 | 8.9 | Halanda | Benedikovic | |
| WINGS | 22 Flap | 22-4 -> 22-9 Ribs & Subassemblies attached. Spar, trailing edge and skins dimpled | 22/5/2016 | 10.5 | Halanda | Benedikovic | |
| WINGS | 22 Flap | 22-4 -> 22-9 Ribs & Subassemblies attached. Trailing edge pro-sealed and clecoed for overnight. | 23/5/2016 | 10.6 | Halanda | Benedikovic | |
| WINGS | 22 Flap | 22-4 -> 22-9 Trailing Edge riveted | 24/5/2016 | 5.8 | Halanda | Benedikovic | |
| WINGS | 18 Fuel Tank | Balloon leak test | 4/6/2016 | 0.5 | Halanda | Benedikovic | Successful balloon leak test on 'L' fuel tank. |
| WINGS | 18 Fuel Tank | Balloon leak test | 5/6/2016 | 0.5 | Halanda | Benedikovic | 'R' tank balloon bursted overnight, replaced in the morning |
| WINGS | 18 Fuel Tank | Balloon leak test | 6/6/2016 | 0.2 | Halanda | Benedikovic | 'R' tank balloon leak test successful after 24hrs |
| WINGS | 17 Outboard Leading Edge | 17-2 -> 17-4 Assembly, Deburring, Dimpling of skins and ribs. | 6/6/2016 | 8.5 | Halanda | Benedikovic | |
| WINGS | 17 Outboard Leading Edge | 17-2 -> 17-4 Preparation / Priming | 7/6/2016 | 10.5 | Halanda | Benedikovic | |
| WINGS | 17 Outboard Leading Edge | 17-2 -> 17-4 Preparation / Priming | 8/6/2016 | 11 | Halanda | Benedikovic | |
| WINGS | 17 Outboard Leading Edge | 17-2 -> 17-4 Riveting of outboard ribs, cutting of the 'servie door' | 9/6/2016 | 11 | Halanda | Benedikovic | |
| WINGS | 17 Outboard Leading Edge | 17-2 -> 17-4 Re-Assembly / glecoing for final riveting | 10/6/2016 | 3.5 | Halanda | Benedikovic | |
| WINGS | 17 Outboard Leading Edge | 17-2 -> 17-4 Final riveting | 11/6/2016 | 7.5 | Halanda | Benedikovic | |
| WINGS | 13 Main Spar | Surface control & deburring | 15/8/2016 | 6.5 | Halanda | Benedikovic | |
| WINGS | 13 Main Spar | 13-1 -> 13-5 preparation & priming parts | 16/8/2016 | 8 | Halanda | Benedikovic | |
| WINGS | 13 Main Spar | 13-1 -> 13-5 Web extension installation, countersinking | 18/8/2016 | 6.5 | Halanda | Benedikovic | |
| WINGS | 13 Main Spar | 13-1 -> 13-5 Nutplate install | 19/8/2016 | 9 | Halanda | Benedikovic | |
| WINGS | 13 Main Spar | 13-1 -> 13-5 Tie down bracket & aileron bracket install, predrilling | 21/8/2016 | 7 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-1 -> 14-6 Deburring edges | 22/8/2016 | 10 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-1 -> 14-6 Deburring edges, shaping | 23/8/2016 | 10 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-1 -> 14-6 Applying primer on wing ribs, pre-attachement with clecos | 25/8/2016 | 8.8 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-1 -> 14-6 Riveting Flap Hinge Assemblies and Torque tube support bracket | 26/8/2016 | 9.5 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-1 -> 14-6 Riveting Flaps to main spar | 05/9/2016 | 5.5 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-1 -> 14-6 Riveting Flaps to main spar | 06/9/2016 | 6.5 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-1 -> 14-6 various | 06/9/2016 | 7 | Halanda | Benedikovic | |
| WINGS | 14 Wing Ribs | 14-6 Bolts installation | 07/9/2016 | 3.5 | Halanda | Benedikovic | |
| WINGS | 15 Rear Spar | 15-1 -> 15-4 Deburring, preparation | 10/9/2016 | 9.5 | Halanda | Benedikovic | |
| WINGS | 15 Rear Spar | 15-1 -> 15-4 Deburring, preparation & priming of parts | 11/9/2016 | 10.5 | Halanda | Benedikovic | |
| WINGS | 15 Rear Spar | 15-2 Aileron bracket assy finished, pushrod hole copied | 12/9/2016 | 8 | Halanda | Benedikovic | |
| WINGS | 15 Rear Spar | 15-4 Final assembly / riveting | 13/9/2016 | 8 | Halanda | Benedikovic | |
| WINGS | 15 Rear Spar | 15-4 Final assembly / riveting | 14/9/2016 | 5.5 | Halanda | Benedikovic | |
| WINGS | 16 Top Wing Skins | 16-1 -> 16-4 Deburring, Dimpling | 18/9/2016 | 7.5 | Halanda | Benedikovic | |
| WINGS | 16 Top Wing Skins | 16-1 -> 16-4 Deburring, Dimpling | 19/9/2016 | 9.5 | Halanda | Benedikovic | |
| WINGS | 16 Top Wing Skins | 16-1 -> 16-4 Priming | 20/9/2016 | 4.5 | Halanda | Benedikovic | |
| WINGS | SB 16-03-28 | Unboxing / Inventory | 24/9/2016 | 0.5 | Halanda | Benedikovic | Van's Service Bulletin SB 16-03-28 arrived |
| Transport | 28/9/2016 | 8 | Halanda | Moving Tailcone, Fin and Stab to a new location to free up some space.. | |||
| WINGS | SB 16-03-28 | Disassembly of the old brackets to extract the original bearings. Deburring, priming, painting, assembly & riveting. | 25/10/2016 | 9.25 | Halanda | Benedikovic | Van's Service Bulletin SB 16-03-28 APPLIED |
| WINGS | 20 BOTTOM WING SKINS | 20-4 Preparation and installation of GAP FAIRINGS incl. Stiffeners | 26/10/2016 | 8.5 | Halanda | Benedikovic | |
| WINGS | 16 Top Wing Skins | 16-3 Preparation and riveting of the top skin (L Wing) | 27/10/2016 | 6.7 | Halanda | Benedikovic | |
| ELECTRIC AILERON TRIM | OP-38 | OP38-2 -> OP38-4 preparation of parts, deburring, priming and assembly | 27/10/2016 | 4 | Halanda | Benedikovic | |
| WINGS | 20 BOTTOM WING SKINS | 20-5 Deburring, dimpling & priming of bottom skins. Attaching fasteners | 28/10/2016 | 5 | Halanda | Benedikovic | |
| WINGS | 20 BOTTOM WING SKINS | 20-5 Deburring, dimpling of Access plates | 30/10/2016 | 2 | Halanda | Benedikovic | |
| ELECTRICAL | Corrugated Conduit | 09/11/2016 | Halanda | Purchase of 12m | |||
| WINGS | Rivets | Inventory of missing rivets | 21/11/2016 | 0.1 | Halanda | Added & inventory of missing rivets: 120 and 100pcs respectively | |
| Enhancements | Wing LNDG lights | Cutouts in R leading edges | 09/12/2016 | 4.5 | Halanda | Benedikovic | |
| Enhancements | Wing LNDG lights | Cutouts in L leading edges; LNDG Brackets installation | 10/12/2016 | 8.5 | Halanda | Benedikovic | |
| WINGS | 16 TOP WING SKINS | 16-3 Riveting the top wing skins (missing row with AN426AD3-4 | 10/12/2016 | 1.2 | Halanda | Benedikovic | |
| WINGS | 17 OUTBOARD LEADING EDGE | 17-4 L & R outboard leading edges riveted to main spar assy | 11/12/2016 | 5.5 | Halanda | Benedikovic | |
| Purchase of wood for the wing cart | 12/12/2016 | 3 | Halanda | ||||
| Wing cart assembly | 12/12/2016 | 5.75 | Halanda | Credit for the idea and plans goes to Mouser! We have used your plans with light modifications. THANK YOU | |||
| WINGS | 18 FUEL TANKS | Priming | 12/12/2016 | 1.75 | Halanda | Benedikovic | |
| WINGS | 18 FUEL TANKS | Attaching Fuel tanks to main spar assy. | 13/12/2016 | 4.5 | Halanda | Benedikovic | Tanks had to be removed twice due to overlaping skins.. Very tight fitment. |
 | 15/12/2016 Inspected by The Transport Authority of Slovak Republic | ||||||
| WINGS | 23 Aileron Actuation | Preparation, shortening the pushrods to required length, drilling, riveting and priming the parts. | 03/03/2017 | 9.5 | Halanda | Benedikovic | |
| WINGS | 23 Aileron Actuation | Installation | 04/03/2017 | 2 | Halanda | Benedikovic | |
| PITOT STATIC SYSTEM | PITOT STATIC SYSTEM | Preparation, drilling. Ready for final assembly | 05/03/2017 | 7.5 | Halanda | Benedikovic | |
| PITOT STATIC SYSTEM | Static ports, hardware and tube | Inventory | 06/03/2017 | 0.1 | Halanda | Inventory CLEVELAND T. Static KIT | |
| ELECTRICAL & AVIONICS | VOR/ILS RAMI Antenna | Inventory | 06/03/2017 | 0.1 | Halanda | Inventory RAMI AV-520 | |
| TRANSPORTS & PAINTJOB | Transport of assembled parts and preparation of new workshop | 26/11/2017 | 11.5 | Benedikovic | Moving tailcone and wings to new workshop. | ||
| ELECTRICAL & AVIONICS | VOR/ILS Antenna | Preparation & Installation | 01/12/2017 | 5 | Halanda | Benedikovic | |
| PITOT STATIC SYSTEM | PITOT STATIC SYSTEM | Prime & Installation | 01/12/2017 | 0.5 | Halanda | Benedikovic | |
| PITOT STATIC SYSTEM | Static ports Installation | Installation and bonding with Araldite 420 | 05/12/2017 | 2.3 | Halanda | Benedikovic | |
| ELECTRIC AILERON TRIM | OP-38 Electric Aileron Trim to Access Door Attach | OP38-2 -> OP38-4 Attaching the trim unit to Wing Access Door | 05/12/2017 | 0.5 | Halanda | Benedikovic | |
| EMPENNAGE | 11 Empenage Attach | 11-4 Fabricating and attaching shims | 19/12/2017 | 3 | Halanda | Benedikovic | |
| Enhancements | Wing LNDG lights | Installation of the Light holders/frame and plexi glass | 31/01/2018 | 8 | Halanda | Benedikovic | |
| EMPENNAGE | 11 Empenage Attach | 11-4, 11-5 Attaching and match drilling the horizontal stabilizer to empennage | 02/02/2018 | 8.5 | Halanda | Benedikovic | |
| EMPENNAGE | 11 Empenage Attach | Closing the inner side of the VS Tip Fairing & fine tuning its leading edge with micro balloons | 06/02/2018 | 3 | Halanda | Benedikovic | |
| EMPENNAGE | 11 Empenage Attach | Closing the inner side of the VS Tip Fairing & fine tuning its leading edge with micro balloons | 07/02/2018 | 1 | Halanda | Benedikovic | |
| EMPENNAGE | 11 Empenage Attach | 11-6 Pushrod Assembly | 07/02/2018 | 2 | Halanda | Benedikovic | |
| Enhancements | BERINGER Brakes | Arrival, Inventory, Pre-assembly | 09/02/2018 | 3 | Halanda | Benedikovic | |
| Enhancements | LANDING LIGHTS | Inventory & function test | 26/02/2018 | 0.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | Inventory | 05/03/2018 | 9 | Benedikovic | Kit Inventory | ||
| FUSELAGE KIT | Inventory | 06/03/2018 | 8.5 | Benedikovic | Kit Inventory | ||
| FUSELAGE KIT | 25 MID FUSE BULKHEADS | 25-2 -> 25-5 Basic preparation, priming, riveting.. | 07/03/2018 | 8 | Halanda | Benedikovic | |
| FUSELAGE KIT | 25 MID FUSE BULKHEADS | 25-5 -> 25-8 BOLTING THE AFT BULKHEAD TOGETHER; REAR SPAR BULKHEAD ASSEMBLY; FUSELAGE BULKHEAD ASSEMBLY | 08/03/2018 | 9.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 25 MID FUSE BULKHEADS | 25-5 -> 25-8 BOLTING THE AFT BULKHEAD TOGETHER; REAR SPAR BULKHEAD ASSEMBLY; FUSELAGE BULKHEAD ASSEMBLY | 09/03/2018 | 8.7 | Halanda | Benedikovic | |
| FUSELAGE KIT | 25 MID FUSE BULKHEADS | 25-7 -> 25-8 Drilling, Deburring, Priming, Riveting the REAR SPAR BULKHEAD ASSEMBLY & FUSELAGE BULKHEAD ASSEMBLY | 13/03/2018 | 8.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-2 -> 26-4 Procedure according plans | 14/03/2018 | 6.8 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-2 -> 26-4 Procedure according plans | 15/03/2018 | 4.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-2 -> 26-4 ATTACHING SEAT RIB SUBASSEMBLIES TO THE AFT CENTER SECTION BULKHEAD SUBASSEMBLY | 16/03/2018 | 8.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-2 -> 26-4 Preparation of rear spar bulkhead ribs | 17/03/2018 | 7.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-2 -> 26-4 RIB ATTACH TO REAR SPAR BULKHEAD | 18/03/2018 | 9 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-5 -> 26-6 RIB TO FUSELAGE BULKHEAD ATTACH | 19/03/2018 | 9 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-7 -> 26-8 BOTTOM SKINS - Dimpling, Deburring, Priming +glecoed to ribs | 20/03/2018 | 6.5 | Halanda | Benedikovic | |
| Enhancements | STEP MOUNT | Fabrication, Priming, Drilling & Riveting the additional support bracket | 26/03/2018 | 3 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-7 -> 26-8 BOTTOM SKINS -glecoed to ribs | 26/03/2018 | 1 | Halanda | Benedikovic | |
| FUSELAGE KIT | 27 FIREWALL | 27-2 BULKHEAD ASSEMBLY -preparation, drilling, deburring, priming, riveting | 27/03/2018 | 7.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 27 FIREWALL | 27-2 BULKHEAD ASSEMBLY -preparation, drilling, deburring, priming, riveting | 28/03/2018 | 2 | Halanda | Benedikovic | |
| FUSELAGE KIT | 26 MID FUSE RIBS & BOTTOM SKINS | 26-7 -> 26-8 BOTTOM SKINS rivetiting | 29/03/2018 | 4.5 | Benedikovic Jr. & son Misko | Benedikovic | |
| FUSELAGE KIT | 27 FIREWALL | 27-2 -> 27-5 works according plans | 30/03/2018 | 8 | Halanda | Benedikovic | |
| FUSELAGE KIT | 27 FIREWALL | 27-2 -> 27-5 works according plans | 01/04/2018 | 7.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN | 28-4 DRILL AND TRIM CONTROL COLUMN MOUNT | 04/04/2018 | 3 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN | 28-2 -> 28-6 DRILLING, DEBURRING, PRIMING & ASSEMBLY WITH CLECOS | 05/04/2018 | 7.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN | 28-5 FINAL DRILL BOTTOM SKIN, MATCH-DRILL CONTROL COLUMN MOUNT | 06/04/2018 | 4.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN | 28-5 Priming FUSE FLOOR RIBS & various parts, Dimpling FWD BOTTOM SKIN | 09/04/2018 | 5.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN, 27 FIREWALL | 28-5, 28-6, 28-8, 28-11, 27-6 (HI LOKs used instead of regular rivets) Procedure according Constr. Plans | 11/04/2018 | 7.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN | 28-9 MATE MID FUSELAGE ASSEMBLY TO FORWARD FUSELAGE ASSEMBLY + SKIN OVERLAP (CLECOED) | 13/04/2018 | 3.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN | 28-9 MATE MID FUSELAGE ASSEMBLY TO FORWARD FUSELAGE ASSEMBLY. F-1004K-L & R Center Section Side Plates (primed, clecoed & partially riveted) | 15/04/2018 | 4.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS, BHDS & BOTTOM SKIN | 28-16 -> 28-17 DRILLING THE LANDING GEAR MOUNT | 18/04/2018 | 3.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-2 -> 29-4 Fabricating BENDING & CLAMPING BLOCKS + Bending LONGERONS | 19/04/2018 | 7.25 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-4 -> 29-5 | 20/04/2018 | 8 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-5 -> 29-10 | 21/04/2018 | 7 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-5 -> 29-10 | 22/04/2018 | 4 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-5 -> 29-10 | 25/04/2018 | 7.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Received SWITCH GUARDS & PIEZOELECTRIC BUZZER (Stall Warning) | 29/04/2018 | 0.5 | Halanda | Inventory | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-12 -> 29-14 per plans | 01/05/2018 | 7.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 27 FIREWALL | Problem discovered: rivets out of spec | 03/05/2018 | 0.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 38 RUDDER PEDALS & BRAKE SYSTEM | 38-2 Creating Brake Pedals | 03/05/2018 | 3 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-19 Vent Doors: Cutting brackets and slides apart; Assembling the doors; Priming; Riveting, Assembling doublers and brackets. | 03/05/2018 | 2 | Halanda | Benedikovic | |
| FUSELAGE KIT | 39 CONTROL SYSTEM | 39-6 Fabricated spacer, drilled, primed & riveted the Elevator Idler Arm. | 03/05/2018 | 1 | Halanda | Benedikovic | |
| FUSELAGE KIT | 27 FIREWALL | Removing the bracket with rivets out of spec WD-1002-L-PC | 03/05/2018 | 1.25 | Halanda | Benedikovic | |
| FUSELAGE KIT | 30 STEP INSTALLATION | 30-2 -> 30-4 Installing steps with additional stiffening plates riveted from the backside of where the delrin is mounted. Additionaly step bushings from TCW Tech were added. | 04/05/2018 | 3.25 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | 29-5 ; 29-8 ; 29-17 (deburring, dimpling, bending, priming) | 12/05/2018 | 2.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 35 ACCESS COVERS AND FLOOR PANELS | 35-2 (Floor panels installation) | 12/05/2018 | 1.5 | Halanda | Benedikovic | |
| INVENTORY | Spare & Replacement Parts | Spare & Replacement parts | 14/05/2018 | 0.25 | Halanda | Spare & Replacement Parts from Vans | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS / 30 Step Installation | Glecoed Side Skins & Steps Priming | 14/05/2018 | 3.5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | Access / Inspection Covers, 33 Baggage Area | (33-2) Baggage Floors w. Inspection Covers | 16/05/2018 | 5.5 | Halanda | Benedikovic | |
| INVENTORY | Spare & Replacement Parts | Received the replacement bracket from Vans with spare parts as well as rivets and brake hoses. | 29/06/2018 | 0.3 | Halanda | ||
| ENHANCEMENTS | Access / Inspection Covers | Cutting an opening for the tunnel access/inspection cover. | 30/06/2018 | 1.5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | 27 FIREWALL, BERINGER Brakes, 38 URDDER PEDALS & BRAKE SYSTEM | Installing the Rudder Pedal Bearing Block together with the Beringer Parking Brake Valve on the Pilot’s side & replacing the WD-1002-L-PC bracket which was removed before due to rivets out of spec | 03/07/2018 | 5.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | Riveting the Side Skins. | 04/07/2018 | 3.5 | Halanda, Benedikovic Jr. | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | (29-18) Glecoing the FWD Side Skins. | 05/07/2018 | 0.5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | 29 FUSE SIDE SKINS, ACCESS / INSPECTION COVERS | (33-2) Preparing the seat floors according to plans + creating access/inspection openings. | 07/07/2018 | 5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | 29 FUSE SIDE SKINS, ACCESS / INSPECTION COVERS | (33-2) Seat Floors - Openings were drilled for goose necks which will be covered by the side panels. Parts primed and nutplates riveted. | 09/07/2018 | 8.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | (29-18) FWD Side Skins- Karol B. Jr. riveting the FWD Side Skins today.. | 14/07/2018 | 3.75 | Benedikovic Jr. | Benedikovic | |
| FUSELAGE KIT | 31 UPPER FWD FUSELAGE ASSEMBLY | (31-1 -> 31-10) Starting works on Section 31 (following plans, basic preparation) | 15/07/2018 | 5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 31 UPPER FWD FUSELAGE ASSEMBLY | (31) Dimpling, Deburring & Priming Parts | 16/07/2018 | 3 | Halanda | Benedikovic | |
| FUSELAGE KIT | 31 UPPER FWD FUSELAGE ASSEMBLY | (31) ..works continue on Upper FWD Fuse Assy, Upper skin dimpled & glecoed | 17/07/2018 | 4 | Halanda | Benedikovic | |
| FUSELAGE KIT | 31 UPPER FWD FUSELAGE ASSEMBLY | (31) Upper FWD Fuse Assy - preparations finished, ready for final riveting. | 18/07/2018 | 2.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 32 TAILCONE ATTACHEMENT | 32-1 -> 32-6 Tailcone Attachement - following plans | 19/07/2018 | 7.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 30 STEP INSTALLATION | (30) Following plans | 20/07/2018 | 4 | Halanda | Benedikovic | |
| FUSELAGE KIT | 32 TAILCONE ATTACHEMENT | Riveting the tailcone with fuse together as called out in the plans. | 22/07/2018 | 4.8 | Halanda | Benedikovic | |
| FUSELAGE KIT | 40 FLAP SYSTEM | (40-4 -> 40-8) As called out in the plans. | 23/07/2018 | 6 | Halanda | Benedikovic | |
| INVENTORY | ANDAIR Fuel System | Inventory and inspection of ANDAIR components. Consisting of: Fuel Pump, Fuel Valve Selector with ext. rod, 2 Gascolators (one for each wing) | 24/07/2018 | 1 | Halanda | ||
| FUSELAGE KIT | 32 TAILCONE ATTACHEMENT | (32) Last rivets set to attach both main parts.. | 27/07/2018 | 2.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 28 FWD FUSE RIBS BHDS BOTTOM SKINS | (28) Riveting panels in place. | 27/07/2018 | 3.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 29 FUSE SIDE SKINS | (29-21) Installing the Landing Gear Mount. | 28/07/2018 | 4.75 | Halanda | Benedikovic | |
| ENHANCEMENTS | ELECTRICAL CONDUITS | Installation of Electrical Conduits in fuselage. | 30/07/2018 | 3.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 33 BAGGAGE AREA | (33-1 -> 33-6) Riveting as called out in plans. | 07/08/2018 | 9 | Halanda | Benedikovic | |
| FUSELAGE KIT | 34 BAGGAGE DOOR | Manufacturing the Baggage Door | 10/08/2018 | 7.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Initial 3D Instrument Panel Planing | 15/08/2018 | 9.5 | Halanda | planing | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D Design work continues | 17/08/2018 | 6 | Halanda | planing | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D Designing push buttons & descriptions | 19/08/2018 | 3.5 | Halanda | ||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D Design: Push buttons, Warning Lights & Toggle switches placed on the instrument panel. Looking for the best place with ergonomy. | 20/08/2018 | 4 | Halanda | ||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D Design: Backup EFIS & Master Switch added. | 30/08/2018 | 3 | Halanda | ||
| ELECTRICAL & AVIONICS | ELECTRICAL & AVIONICS | 3D Design: Rendering the panel with 'live' displays and backlit some of the switches for visualization. | 03/09/2018 | 4.5 | Halanda | ||
| FUSELAGE KIT | 42 REAR SEAT BACKS | (42) Manufacturing Rear Seat Backs | 05/09/2018 | 5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | 37 FUEL SYSTEM, ANDAIR FUEL SYSTEM | Manufacturing the fuel lines to the gascolators and finding a suitable place to mount them. Both gascolators will be hidden in the wing roots. | 06/09/2018 | 2 | Halanda | Benedikovic | |
| FUSELAGE KIT | 42 REAR SEAT BACKS | (42) Rear Seat Backs primed & mounted | 06/09/2018 | 3 | Halanda | Benedikovic | |
| FUSELAGE KIT | 37 FUEL SYSTEM, 38 RUDDER PEDALS & BRAKE SYSTEM | (38 & 37)Brake & Fuel Lines installation | 07/09/2018 | 7.75 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D Design: I have redesigned the pushbutton for disconnecting all autopilot servos/trim & flap motors with one button.. | 09/09/2018 | 1.5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | 37 FUEL SYSTEM, ANDAIR FUEL SYSTEM | Fabricating, priming & installing mount brackets for both ANDAIR gascolators. | 09/09/2018 | 3.5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | 37 FUEL SYSTEM, ANDAIR FUEL SYSTEM | The bracket looks a bit complicated; the goal was to have the fuel pump easily accessible from the Inspection Access Hatch. Fabricated the fuel line from the ANDAIR fuel selector to the ANDAIR fuel pump. This fuel pump features an internal bypass. | 11/09/2018 | 6.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 39 CONTROL SYSTEM | Installing the rudder cables with fairings. | 12/09/2018 | 3.25 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Rendering with the new switch. I am not happy with the current location and will most likely move it to the left side of the panel. | 13/9/2018 | 1.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 39 CONTROL SYSTEM | Installation as plans call out. Rudder pedals powder coated black. | 13/09/2018 | 7.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 39 CONTROL SYSTEM, 40 FLAP SYSTEM | Respective chapters -following plans. | 14/09/2018 | 9 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | BERINGER BRAKES, 38 RUDDER PEDALS & BRAKE SYSTEM | Rudder Pedals with Beringer Master Cylinders installation. | 15/09/2018 | 4.5 | Halanda | Benedikovic | |
| FUSELAGE KIT, ENHANCEMENTS | BERINGER BRAKES, 38 RUDDER PEDALS & BRAKE SYSTEM | Installation of BERINGER Hydraulic brake houses. Following BERINGER installation manual. | 18/09/2018 | 6.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 44 WING ATTACHEMENT | Priming the skin and installing the root fairing supports on the fuselage skin. | 19/09/2018 | 5.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 39 CONTROL SYSTEM | (39) Finishing Rudder Cables installation. | 21/09/2018 | 2.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | RUDDER TRIM | Manufacturing a Rudder Trim prototype. The trim will actuate directly on the rudder pedals with the help of an electrical servo motor. Finding the proper spring length with proper tension will be a challenge. | 23/09/2018 | 4.5 | Halanda | Benedikovic | Prototype |
| ENHANCEMENTS | RUDDER TRIM | Servo motor installed and connected to the copilot’s left rudder pedal. | 25/09/2018 | 4 | Halanda | Benedikovic | Prototype (Won't be connected during initial test flights) |
| INVENTORY | ANDAIR FUEL SYSTEM COMPONENTS | ANDAIR elbows, blanking plugs and drain valves for both fuel gascolators. | 02/10/2018 | 0.25 | Halanda | ||
| ENHANCEMENTS | ACCESS / INSPECTION COVERS | Manufacturing and riveting the backplate with nutplates to the tunnel acccess/inspection cutout. | 02/10/2018 | 2.5 | Halanda | Benedikovic | |
| INVENTORY | Fans, Grills & Lemo Plugs | Defrost Fans with Grills & DC Lemo Plug Install Kit | 03/10/2018 | 0.25 | Halanda | ||
| ENHANCEMENTS | OP-41 | ELT bracket drilled, primed and riveted nutplates, finally riveted in the e-bay/battery compartment. | 03/10/2018 | 2.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 44 WING ATTACHEMENT | (44) Manufacturing and priming Wing Root Fairings as called out in plans. | 03/10/2018 | 3.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | ANDAIR FUEL SYSTEM | Installing ANDAIR plugs, elbows & drain valves on each gascolator. | 04/10/2018 | 0.75 | Halanda | Benedikovic | |
| ENHANCEMENTS | OVERHEAD CONSOLE / SYSTEM | NACA Cutouts for Overhead Fresh Air | 04/10/2018 | 2 | Halanda | Benedikovic | |
| FINISH KIT | 50 CABIN HEAT & VENTILATION | (50) PIC & COPI Front NACA Vents installed. | 08/10/2018 | 3.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | ACCESS / INSPECTION COVERS | Rear Bulkhead Access Door Cutout: Cutout was done using a water jet. The access will be hinged on the upper part to allow quick and easy access to the battery / electronic-bay. | 09/10/2018 | 8 | Halanda | Benedikovic | |
| ENHANCEMENTS | ACCESS / INSPECTION COVERS | Rear Bulkhead Access Door: Completed with 2 locking latches and primed on the battery/e-bay side. | 10/10/2018 | 7.5 | Halanda | Benedikovic | |
| INVENTORY | New Parts Arrival | Inventory of items: Door Strut Attach Brackets (Planearound), New Door 180 Kit (Planearound), Wheel Bracket Fairing Spacers (Planearound), Angled Door Pins & Delrin Pin Guides (Planearound), Sirs Light Aircraft Compass, Rudder Pedal Extensions from (JD Air), Infinity Grips, Carling backlit (Mom ON-OFF-ON Mom) Switches and Blends. | 11/10/2018 | 1 | Halanda | ||
| FUSELAGE KIT | 31 UPPER FWD FUSELAGE ASSEMBLY | (31-2 -> 31-9) Riveting the Subassembly to Fuselage, FWD Fuse Top Skin dimpled & Rear Bulkhead primed from the cabin side. | 11/10/2018 | 2 | Halanda | Benedikovic | |
| FUSELAGE KIT | 33 BAGGAGE AREA | (33-10) Installing the Wear Blocks to the Baggage Bulkhead. | 11/10/2018 | 1.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 43 CABIN COVER | (43) Started works on the repaired Cabin Cover & first test fit. | 15/10/2018 | 9.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 43 CABIN COVER | (43-1 -> 43-13) Triming & Match Drilling Cabin Top. | 16/10/2018 | 8.75 | Halanda | Benedikovic | |
| INVENTORY | Various new parts arrival | ROSEN Sun Visors, SUPERIOR PANEL TECHNOLOGY Light Strip, External Power Receptacle, External Power Plug, Electrical Cables, Pitot / Static Tube System, Antennas (Marker Beacon, DME, TXPD, ADS-B, FLARM, 2xVHF), Ray Allen POS-12 Position Sensor, Hidden Oil Door Hinge & various fittings, grommets, New primer spray cans from Colorlak | 16/10/2018 | 1 | Halanda | ||
| ENHANCEMENTS, ELECTRICAL & AVIONICS, PITOT STATIC SYSTEM | PEDAL EXTENSIONS, WING ELECTRICS, PITOT STATIC SYSTEM | Installing Corrugated Conduits in Wings, grommets in the fuselage to protect conduits, JD Pedal Extensions, Pitot & AOA tubes in L Wing. | 18/10/2018 | 6 | Halanda | Benedikovic | |
| PITOT STATIC SYSTEM | PITOT STATIC SYSTEM | Static System Installation in tailcone. | 21/10/2018 | 4 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS, PITOT STATIC SYSTEM | External Power Connector, PITOT STATIC SYSTEM | Works continued on the Pitot Static system (Wings – Fuselage Attach Points). 3D printing conduit holders for the Electronic / Battery Bay Compartment & Ext Power Plug Cover. Manufacturing the Baseplate for the Ext Power Connector incl a switch (for either charging the battery with a regulated Ext Pwr or unregulated for engine start only). | 22/10/2018 | 6 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | External Power Connector | External Power Connector Base Plate: Finished, primed & installed. | 23/10/2018 | 4 | Halanda | Benedikovic | |
| FUSELAGE, ENHANCEMENTS | 40 FLAP SYSTEM, FLAP POSITION SENSOR | Manufacturing, priming and installation of an L-Bracket for the Flaps Position sensing. | 23/10/2018 | 3 | Halanda | Benedikovic | |
| WINGS | 20 BOTTOM WING SKINS | (20-5 -> 20-6) Riveting Inboard Bottom Skins on both wings. | 25/10/2018 | 5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Cutting holes for 2 Defrost/Avionics Cooling Fans. The SilverStone 80mm grills will be mounted from below. | 26/10/2018 | 1.5 | Halanda | Benedikovic | |
| WINGS | 20 BOTTOM WING SKINS | (20-5 -> 20-6) Riveting Outer Bottom R-Wing Skin. | 31/10/2018 | 3.5 | Halanda | Benedikovic | |
| WINGS | 24 WING TIP | (24) Wing Tip R-Wing. Installing the wing tip on R-wing using hinges (Mouser method). | 05/11/2018 | 6.75 | Halanda | Benedikovic | |
| INVENTORY | Various parts received | GARMIN Pitot with regulator, GARMIN AutoPilot Servos with Connector Kits, Limit switches mechanical & reed sensor, ANDAIR Oil / Air Separator | 07/11/2018 | 0.75 | Halanda | ||
| WINGS | 24 WING TIP | (24) Wing Tip R-Wing; ..works continue, riveted & bonded with Araldit. Manufactured carbon fiber rib (to copy aileron trailing edge) installed. | 07/11/2018 | 6 | Halanda | Benedikovic | |
| ENHANCEMENTS | EXTERIOR LIGHTS | 11/11/2018 | 3 | Halanda | Benedikovic | ||
| WINGS, ENHANCEMENTS, ELECTRICAL & AVIONICS | ANTENNAS, 24 WING TIP, EXTERIOR LIGHTS | Landing Light Bracket Primed & Installed with light, (24) filling the gap between wing & wing tip, ADS-B IN Antenna installation. | 13/11/2018 | 6.75 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS, ENHANCEMENTS | WINGS, OP38 ELECTRIC AILERON TRIM | GARMIN Auto Pilot Roll Servo & Roll Trim Servo springs installed. Following Vans & Garmin install manual. | 15/11/2018 | 3.75 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS, ENHANCEMENTS | FUSELAGE | GARMIN Auto Pilot Pitch Servo installed - following Garmin install manual. | 17/11/2018 | 2.75 | Halanda | Benedikovic | |
| PITOT STATIC SYSTEM | PITOT STATIC SYSTEM | Installing Heated & Regulated GARMIN Pitot Tube + looking for a good place for installing the regulator. | 19/11/2018 | 1.5 | Halanda | Benedikovic | |
| INVENTORY | Connectors & Push/Pull Cables received. | INVENTORY TE DT&DTM Deutsch Connectors & Push/Pull Cables. | 22/11/2018 | 2 | Halanda | ||
| WINGS, PITOT STATIC SYSTEM | 20 BOTTOM WING SKINS | (20-5 -> 20-6) Riveting Outer Bottom L-Wing Skin. Installation of Pitot Tube with Gretz Mast finished. | 22/11/2018 | 4.5 | Halanda | Benedikovic | |
| WINGS | 24 WING TIP | (24) Wing Tip L-Wing. Same process and method like done and documented on R-Wing.. | 24/11/2018 | 6 | Halanda | Benedikovic | |
| WINGS | 24 WING TIP | (24) Wing Tip L-Wing ..works continue. Leaving the Araldit bond to cure close to the source of heat. | 26/11/2018 | 4.5 | Halanda | Benedikovic | |
| INVENTORY | BERINGER BRAKES received | BERINGER FUSELAGE KIT: Wheels, Brakes (with floating calipers), tubes, brake bleeding kit & components incl. tire changing tools for different tire sizes received. | 27/11/2018 | 1 | Halanda | ||
| WINGS | 24 WING TIP | (24) Wing Tip L-Wing - Finishing the works on the Left Wing Tip. Carbon fiber rib installed & gap filled with EPOXY and micro between wing skin and tip. | 30/11/2018 | 2.75 | Halanda | Benedikovic | |
| INVENTORY | Switches | Flap Switch & Alternate Static Air Source switch - Honeywell MicroSwitch (Mom ON-OFF-Mom ON). The Alt Static Air Source switch will open a hole in the switch body to allow for alternate static cabin air source in case both outer static sources get plugged. | 03/12/2018 | 0.25 | Halanda | ||
 | 11/12/2018 Inspected by The Transport Authority of Slovak Republic | ||||||
| PITOT STATIC SYSTEM, ELECTRICAL & AVIONICS | Garmin Pitot Heat Regulator mounted | 11/12/2018 | 2.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Flap Switch Actuator 3D design for the Instrument Panel visualization. | 18/12/2018 | 1 | Halanda | ||
| ELECTRICAL & AVIONICS | ANTENNAS | Mounting the VHF, TXPD & Marker Beacon Antennas on the belly. | 18/12/2018 | 6 | Halanda | Benedikovic | |
| INVENTORY | -Door gas struts (Bansbach B0N0F50-100-247/530N Gas Spring 4″(100mm) Stroke 10″(247mm) A1 M8 Hinge Eye -have to order E2 M8 to fit the Plane Around attach brackets. -Push & Pull controls for heating, parking brake and Engine Alternate Air -firewall passthrough | 18/12/2018 | 0.25 | Halanda | |||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Instrument Panel 3D visualization with Flaps Actuator&Switch | 19/12/2018 | 2.5 | Halanda | ||
| EMPENAGE KIT | 12 EMPENAGE FAIRINGS | (12-5 -> 12-6) Starting adjustments and installation of the tailcone fairing. | 19/12/2018 | 3 | Halanda | Benedikovic | |
| EMPENAGE KIT | 12 EMPENAGE FAIRINGS | (12-5 -> 12-6) Works on tailcone fairing | 21/12/2018 | 3.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Instrument Panel 3D rendering; Backup battery guard removed. Static source guarded switch moved to the left panel + minor changes. | 22/12/2018 | 5.5 | Halanda | ||
| ENHANCEMENTS | EXTERNAL POWER CONNECTOR | Replacing the external power switch with a guarded version for selecting the main battery contactor on or off with external power connected. | 4/1/2019 | 0.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS, EMPENAGE KIT | EXTERNAL POWER CONNECTOR, ANTENNAS, 12 EMPENAGE FAIRINGS | ..works continue on the tailcone fairing + support bracket installed for the external power recept. Finding the right mounting place for the upper VHF antenna. | 4/1/2019 | 6.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Design works on the Instrument Panel: Modeling an Air Vent TRAFFIC MUTE switch added COMPSS LIGHT switch added IND LTS switch repositioned to the R Panel Placing the equipment on the rear instrument wall (sub-panel) | 6/1/2019 | 8.5 | Halanda | ||
| EMPENAGE KIT | 12 EMPENAGE FAIRINGS | Tailcone Fairing finished | 8/1/2019 | 7 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D design work: Added Deuce Schottky Diode Heat Sink & FLARM AT-1 warning system Added Vishay potentiometers for switch backlighting and glareshield | 10/1/2019 | 6 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | ANTENNAS | VHF Antenna Mount on Tailcone | 12/1/2019 | 6.5 | Halanda | Benedikovic | |
| INVENTORY | DEUCE SCHOTTKY DIODE for Essential Bus & Grinder | 15/1/2019 | 0.25 | Halanda | |||
| ENHANCEMENTS | BERINGER Brakes & Parking Brake | Manufacturing and installing a bracket to hold the parking brake sensor & cable. | 16/1/2019 | 4 | Halanda | Benedikovic | |
| ENHANCEMENTS | Misc | Manufacturing the center console for rear seats. | 17/1/2019 | 3 | Halanda | Benedikovic | |
| INVENTORY | Received VISHAY Potentiometers 10kOhm (MIL spec) | 17/1/2019 | 0.25 | Halanda | |||
| ENHANCEMENTS | Misc | Rear Seats Center Console update | 21/1/2019 | 4.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D Design Work: Minor Design Update on the Instrument Panel | 22/1/2019 | 3.5 | Halanda | ||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Getting Mesh Data of the Aerosport 310 Panel | 3/2/2019 | Aerosport 3D panel Mesh Data recieved | |||
| ENHANCEMENTS | OVERHEAD CONSOLE / SYSTEM | Overhead Console Vents & Alu Flanges | 5/2/2019 | 6.5 | Halanda | Benedikovic | |
| WINGS KIT | 24 WING TIP | (24-2) Cee Baylees Wing Tip Lenses | 9/2/2019 | 3.5 | Halanda | Benedikovic | UPDATE: Unfortunately CEE BAYLEES never responded to my complaints. I'll have to order the original ones from Vans.. |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Andair Fuel Valve added to Cockpit Visualization | 12/2/2019 | 1.5 | Halanda | ||
| ENHANCEMENTS | CENTER CONSOLE | Throttle Quadrant Connecting Points | 22/2/2019 | 5.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Fitting the Aerosport 310 panel | 7/3/2019 | 7.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Fitting the Aerosport 310 panel incl. vents | 8/3/2019 | 3 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Fitting the Aerosport 310 panel w. Armrest | 11/3/2019 | 6 | Halanda | Benedikovic | |
| FUSELAGE KIT / ENHANCEMENTS | 37 FUEL SYSTEM / ANDAIR FUEL SYSTEM | (37) Fitting the ANDAIR Fuel Selector to the Aerosport Armrestpanel | 12/3/2019 | 7.5 | Halanda | Benedikovic | |
| INVENTORY / INSTRUMENT PANEL | Inventory: APEM Master & Backup Switches received | 12/3/2019 | .25 | Halanda | |||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Mounting the Aerosport Throttle Quadrant: ..mating the throttle quadrant to the tunnel & the aerosport center console. Made holes for the push&pull cables to operate the parking brake and the alternate engine air in the left side panel and forward & rear heat in the right panel. | 14/3/2019 | 5.5 | Halanda | Benedikovic | |
| INVENTORY | Inventory: ANDAIR Fitting Extensions & Sphere Steel Grommets: Received the Andair Fitting Extensions for the Gascolators to route the tubes downwards + Sphere Steel Grommets for the firewall to accomodate the push/pull cables. | 15/3/2019 | 0.25 | Halanda | |||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Received planes created out of mesh data: ..for the cockpit visualization. | 15/3/2019 | ||||
| ENHANCEMENTS | ANDAIR FUEL SYSTEM | Mounting Andair Fitting Extensions: ..on both sides L & R | 16/3/2019 | 1 | Halanda | Benedikovic | |
| ENHANCEMENTS | INSTRUMENT PANEL | Starting works on the cockpit visualization incl. the 310 panel | 17/3/2019 | 8.5 | Halanda | ||
| ENHANCEMENTS / FUSELAGE KIT | Misc / 27 FIRE WALL | Mounting the Sphere Steel Grommets to the Firewall: ..and checking operation with the push and pull cables. The lowest thing push&pull is there to operate the Alternate Engine Air. | 18/3/2019 | 3.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS / ENHANCEMENTS | INSTRUMENT PANEL / CENTER CONSOLE | Drilling holes for electrical switches | 19/3/2019 | 1.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Details on the Cockpit Visualization: Background and text for flaps UP and DN adjusted. | 20/3/2019 | 0.5 | Halanda | ||
| FINISH KIT | 47 SPINNER & COWLING | (47) Cowl Attach Hinges: (47-6 -> 47-8) Fabricating and riveting the Cowl Attach Hinges. | 20/3/2019 | 3.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Laser test engraving rocker switches | 27/3/2019 | Samples received from our partner company: TECHMIND | |||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Spray painting push buttons & indicators: ..with Black Matte RAL 9005 | 4/4/2019 | 1 | Halanda | ||
| INVENTORY | Inventory: Gas strut attachements, GPS Antennas, Firewall Foil | 18/4/2019 | 0.25 | Halanda | |||
| INVENTORY | Inventory: Arrival of the Finnish Kit | 23/4/2019 | 9 | Halanda | |||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Update on the 3D Cockpit Visualization | 24/4/2019 | 4.5 | Halanda | ||
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Cabin Doors: (45-02 -> 45-03) | 25/4/2019 | 5 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Cabin Doors: (45-02 -> 45-05) | 26/4/2019 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM | (45) Cabin Doors & PlaneAround Door Locking Mechanism: (45-02 -> 45-05) + PlaneAround Door Locking System | 27/4/2019 | 6.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | BERINGER BRAKES & PARKING BRAKE | Parking Brake Sensor Final Installation | 28/4/2019 | 3.5 | Halanda | Benedikovic | |
| FINISH KIT | 46 ENGINE MOUNT & LANDING GEAR | (46) Initial line up and mounting of the Engine Mount: (46-2) …with some initial difficulties to line up the holes | 29/4/2019 | 2.25 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Cabin Doors: Glueing together both halves. | 29/4/2019 | 3.5 | Halanda | Benedikovic | |
| INVENTORY | Inventory: Wheelen Dome Lights: The first is planed to light up the cabin, the second to light up the baggage compartment. | 30/4/2019 | 0.25 | Halanda | Benedikovic | ||
| ENHANCEMENTS | MISC | Sealing the Firewall with RTV | 30/4/2019 | 0.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | OP48 AHRS BRACKET | (OP-48) AHRS BRACKET mount: The bracket will be utilized to hold the DME & TXPD external modules and some more items. | 1/5/2019 | 2.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 31 UPPER FWD FUSELAGE ASSEMBLY | (31) FWD Fuse Top riveted to Fuselage: (31-9) Had to use a spacer on the left half to avoid folded skin. | 2/5/2019 | 2.25 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Flap Handle repainted | 2/5/2019 | 0.75 | Halanda | Benedikovic | |
| INVENTORY | Inventory: Engine Heating Pads 220V, various screws, BOELUBE Paste, Ignition Switch with keylocks | 3/5/2019 | 0.5 | Halanda | |||
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Cabin Doors: (45-02 -> 45-05) | 4/5/2019 | 3.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | OVERHEAD CONSOLE / SYSTEM | NACA Air Inlets for Overhead Tunnel | 4/5/2019 | 3 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Keyed Ignition Switch 3D model added to Panel Visualization | 4/5/2019 | 1.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | MISC | Firewall Heat & Soundproofing Foil applied | 5/5/2019 | 1.5 | Halanda | Benedikovic | |
| FINISH KIT | 50 CABIN HEAT AND VENTILATION | (50-2) Heater Ducts installed | 6/5/2019 | 1 | Halanda | Benedikovic | |
| FINISH KIT | 46 ENGINE MOUNT & LANDING GEAR | Engine Mount | 6/5/2019 | 0.75 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | Cabin Doors: Working on cabin doors.. | 7/5/2019 | 5.5 | Halanda | Benedikovic | |
| INVENTORY | INVENTORY: Except for glecos and some chemicals, I received the door rubber seals.. Trimlok 100 series: 3100B3X1/4A | 13/5/2019 | 0.5 | Halanda | |||
| ENHANCEMENTS / FUSELAGE KIT | OVERHEAD CONSOLE/SYSTEM / 43 CABIN COVER | OVERHEAD CONSOLE: Preparation for gluing in the Overhead Console | 15/5/2019 | 7.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | OVERHEAD CONSOLE/SYSTEM | OVERHEAD CONSOLE: glued in..: Overhead Console glued in including left and right conduit. | 16/5/2019 | 4.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | OVERHEAD CONSOLE/SYSTEM | Sun Shields & Conduits to Overh. Console | 17/5/2019 | 5.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | OVERHEAD CONSOLE/SYSTEM | Conduits / Overhead Console | 20/5/2019 | 5.25 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | ANTENNAS | Top Mounted Antennas: ..installed | 21/5/2019 | 3 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Cabin Doors | 22/5/2019 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Cabin Doors: Right door and cabin will need better alignment.. | 28/5/2019 | 7.5 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Interior Color & Leather pick: Looking for the right interior colors to match the interior handles and Aerosport panels + leather choice. | 17/6/2019 | 2.25 | Halanda | |||
| ENHANCEMENTS / FUSELAGE KIT | OVERHEAD CONSOLE / SYSTEM / 43 CABIN COVER | (43) Match Drilling Cabin Cover: Match drilling the cabin cover with the Overhead Console | 8/7/2019 | 1.25 | Halanda | Benedikovic | |
| ENHANCEMENTS | MISC | Door Seals: Fitting and trimming the door seals. | 11/7/2019 | 6.75 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM | (45) Door Handles & Mechanism: 45-10 -> 45-14 | 12/7/2019 | 7.5 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM | (45) Door Handles & Mechanism: 45-10 -> 45-14 | 13/7/2019 | 6.25 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM | (45) Door Handles & Mechanism: 45-10 -> 45-14 | 17/7/2019 | 4.5 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM | (45) Door Handles & Mechanism: 45-10 -> 45-17 | 19/7/2019 | 3.25 | Halanda | Benedikovic | |
| ENHANCEMENTS | MISC. / OVERHEAD CONSOLE / SYSTEM | Baggage Light Installation: Model: Whelen 7081307 | 22/7/2019 | 0.75 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS / FUSELAGE KIT | MISC. / CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43)(45) Doors and Door Seals: Making a bed of epoxy for the the door seals and epoxying the delrin guides in place on the doors. | 23/7/2019 | 7.5 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS / FUSELAGE KIT | MISC. / CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43)(45) Doors and Door Seals: Right epoxy bed is finished, now on to the left side.. | 26/7/2019 | 6.25 | Halanda | Benedikovic | |
| ENHANCEMENTS | OVERHEAD CONSOLE/SYSTEM / ELECTRICAL CONDUITS | Cabin Top Conduits: Fine tuning the cabin top’s corrugated conduit covers. | 30/7/2019 | 4.75 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Cabin Top furnishing: Preparing/trimming the laminated interior parts for furnishing the cabin top. | 1/8/2019 | 1.75 | Halanda | Benedikovic | ||
| ENHANCEMENTS / FUSELAGE KIT | OVERHEAD CONSOLE/SYSTEM / 43 CABIN COVER | (43) Cabin Cover & Overhead Console System: Filling and sanding the cabin top inside + fabricating a laminated cover for the Center Cabin Brace. | 3/8/2019 | 5.75 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Gas Strut Installation: 45-16 + door attaching brackets modified | 12/8/2019 | 3.5 | Halanda | Benedikovic | |
| FUSELAGE KIT / PAINT/FURNISHING/UPHOLSTERY | 33 BAGGAGE AREA / 43 CABIN COVER | Spray painting with interior color: Spray painting the Cabin Cover/Top and other parts with interior color. | 14/8/2019 | 1.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 43 CABIN COVER | (43) Cabin Cover mating with Fuselage: 43-4 -> 43-7 Final Fitting the Cabin Cover on the Fuselage + Windshield alignement | 15/8/2019 | 8.25 | Halanda | Benedikovic | |
| FUSELAGE KIT | 43 CABIN COVER | (43) Cabin Cover mating with Fuselage: 43-4 -> 43-7 | 16/8/2019 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT / PAINT/FURNISHING/UPHOLSTERY | 45 CABIN DOORS & TRANSPARENCIES | (45) Preparing for Windshield installation: 45-18 -> 45-19 & creating template for the shield leather cover. | 19/8/2019 | 1.5 | Halanda | Benedikovic | |
| PAINT/FURNISHING/UPHOLSTERY | Glareshield paint: 1 layer of epoxy primer + RAL 9017 Matte Black | 20/8/2019 | 0.25 | Halanda | Benedikovic | ||
| FINISH KIT / FUSELAGE KIT | 45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43) (45) Cabin Cover & Doors + Door sills: The door sills are carbon fiber and come from Aerosport. Building covers for the door hinges.. | 21/8/2019 | 3.75 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Door hinge covers | 22/8/2019 | 2.5 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 45 CABIN DOORS & TRANSPARENCIES / ANDAIR OIL SEPARATOR | (45) Door hinge covers & Oil Separator Mount: Andair Oil Separator Mount on the firewall next to the Brake Fluid Reservoir. | 24/8/2019 | 3.75 | Halanda | Benedikovic | |
| FUSELAGE KIT | 43 CABIN COVER | (43) Center Cabin Brace: Mounting the Center Cabin Brace in position.. | 27/8/2019 | 1.25 | Halanda | Benedikovic | |
| ENHANCEMENTS | ANDAIR OIL SEPARATOR | Andair Oil Separator Mount: One more additional support bracket on the upper back side of the separator. | 28/8/2019 | 1.75 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Door gaps & rear windows: Adjusting the door gaps and attaching the rear pax windows with Lord Adhesive (7545A/E). | 2/9/2019 | 4.75 | Halanda | Benedikovic | |
| INVENTORY | INVENTORY: USB Charging Ports: by CommitLift: http://commitlift.com/USBASinstructions.pdf | 2/9/2019 | 0.25 | Halanda | |||
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Door Gaps: ..working on door gaps | 3/9/2019 | 4.25 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Door Gaps | 5/9/2019 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Windows: 45-18 -> 45-19 Glueing in pax windows and windshield. Checking clearance/depth of the Overhead Panel. | 9/9/2019 | 7.5 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Windshield: 45-18 -> 45-19 | 10/9/2019 | 5.5 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Windshield: 45-18 -> 45-19 | 12/9/2019 | 2.75 | Halanda | Benedikovic | |
| FINISH KIT / INVENTORY | 45 CABIN DOORS & TRANSPARENCIES | (45) Windshield + INVENTORY: 45-18 -> 45-19 Received the 12V power plug -it’s intended for the baggage compartment. | 13/9/2019 | 3 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Windshield: 45-18 -> 45-19 | 14/9/2019 | 2.75 | Halanda | Benedikovic | |
| FINISH KIT / FUSELAGE KIT | 45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43)(45) Cabin Top tuning & Windshield: Tuning the cabin top’s B pillars to match the door’s curvature and works on the windshield according to plans.. | 15/9/2019 | 6.25 | Halanda | Benedikovic | |
| PAINT/FURNISHING/UPHOLSTERY | Upholstery professional visit: Today Peter Skrabalek -an upholstery professional and glider pilot visited our Skunk works to check what can be done with the seats and other interior details.. | 16/9/2019 | |||||
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Windows: Glueing in a door window, working on the windshield and fine tuning/sanding the gaps on the pax windows. | 19/9/2019 | 4.5 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Door Windows & Windshield | 20/9/2019 | 5.5 | Halanda | Benedikovic | |
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) Windows: All windows glued in place.. | 21/9/2019 | 1.25 | Halanda | Benedikovic | |
| FUSELAGE KIT | 43 CABIN COVER | (43) Filling transitions between fuselage and Cabin Cover | 22/9/2019 | 8.5 | Halanda | Benedikovic | |
| PAINT/FURNISHING/UPHOLSTERY | First carpets are finished: These belong to the baggage compartment, the actual color is black. Thanks to Stefan Michalicka who did a fantastic job. | 23/9/2019 | |||||
| FINISH KIT | 45 CABIN DOORS & TRANSPARENCIES | (45) More fiberglass around windows: Laying some more fiber around the windows to smooth the transitions.. | 23/9/2019 | 4.5 | Halanda | Benedikovic | |
| PAINT/FURNISHING/UPHOLSTERY | Trimming carpets: Fine tuning the carpet edges to get a proper fit on the floor. Stefan at work.. | 24/9/2019 | 3.5 | Halanda | Benedikovic | ||
| FINISH KIT / FUSELAGE KIT | 45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43)(45) Trimming gaps and transitions: ..never ending story! We wish Vans would deliver a much better fiberglass components. You literally spend weeks with filling, sanding, trimming.. | 24/9/2019 | 4.5 | Halanda | Benedikovic | |
| FINISH KIT / FUSELAGE KIT | 45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43)(45) Trimming gaps and transitions: ..same story today | 25/9/2019 | 7 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 46 ENGINE MOUNT & LANDING GEAR / BERINGER BRAKES & PARKING BRAKE | (46) Landing Gear BERINGER: A deviation from Vans plans using the BERINGER wheels and brakes RV-10 kit. Getting ready for installation. | 28/9/2019 | 3.5 | Halanda | Benedikovic | |
| INVENTORY | INVENTORY Baggage Net and engine mount covers: Today I received the baggage net, both engine mount carbon covers and a handle cover replacement (got damaged during installation). The last 2 items came from AeroSport – super friendly customer service! | 30/9/2019 | 0.25 | Halanda | |||
| FINISH KIT / FUSELAGE KIT | 45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43) (45) More filling and sanding.. | 2/10/2019 | 8.75 | Halanda | Benedikovic | |
| FINISH KIT / FUSELAGE KIT | 45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER | (43) (45) More filling and sanding.. | 3/10/2019 | 9 | Halanda | Benedikovic | |
| ENHANCEMENTS / INVENTORY | INSTRUMENT PANEL | Laser etched switches: Today I received my laser etched switches for the instrument panel from http://techmind.sk/en/ Mr. Martyscak, the owner of Techmind did a wonderful job. I’m very happy with the results.. | 4/10/2019 | ||||
| PAINT/FURNISHING/UPHOLSTERY / FUSELAGE KIT | 43 CABIN COVER | Spray painting the Cabin Cover and Fuse: 2K Epoxy Primer | 8/10/2019 | 5.5 | Halanda | Benedikovic | |
| ENHANCEMENTS / FUSELAGE KIT | BERINGER BRAKES & PARKING BRAKE / 43 CABIN COVER | (43) Cabin Cover finished: voilà | 10/10/2019 | 7.75 | Halanda | Benedikovic | |
| ENHANCEMENTS / FINISH KIT | BERINGER BRAKES & PARKING BRAKE / 46 ENGINE MOUNT & LANDING GEAR | (46) Main & Nose Gear: Right landing gear incl. wheel was attached without issues but the pin on the left side wouldn’t go in and eventually bent. During removal the axle was damaged so I ordered a new one including 2 new pins from BERINGER. Forward leg mounted with rubber dampeners with no issues. We had to utilize a temporary support for the left side until we get replacement parts from BERINGER. | 13/10/2019 | 7 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Starting works on the Wheel Fairings | 15/10/2019 | 6.75 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Wheel Fairings | 17/10/2019 | 7.75 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Gear Legs and Wheel Fairings | 18/10/2019 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Gear Legs and Wheel Fairings | 24/10/2019 | 8.75 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Switch & Pushbutton backlighting: Checking the switch backlighting with some 9V batteries. The pushbutton’s text will be visible when backlit only. | 24/10/2019 | 0.5 | Halanda | ||
| FINISH KIT / ENHANCEMENTS | 48 GEAR LEG & WHEEL FAIRINGS / BERINGER BRAKES & PARKING BRAKE | (48) Left Main Gear attached: The spare parts from BERINGER arrived so we were able to mount the left leg with wheel and did some additional work on the fairings. | 29/10/2019 | 4 | Halanda | Benedikovic | |
| FINISH KIT / ENHANCEMENTS | 48 GEAR LEG & WHEEL FAIRINGS / BERINGER BRAKES & PARKING BRAKE | (48) Forward leg and wheel fairings | 31/10/2019 | 7.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Finding the axes: For a proper wheel pants alignment we raised the main gears and drew axes on the floor.. | 2/11/2019 | 3 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Front leg and wheel fairings | 3/11/2019 | 7.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Main Wheel Fairings: Aligning the main wheel fairings.. | 4/11/2019 | 6 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Main Wheel Fairings | 5/11/2019 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Main Wheel Fairings: Slight deviation from plans: Fabricating a V-bracket to better support the fairing; saw this solution at some other builder’s website and liked it. The single bolt hole will be filled when finished. | 6/11/2019 | 5.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Main Wheel V-brackets: Riveted and epoxied in place.. | 7/11/2019 | 3.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Wheel Fairings | 8/11/2019 | 7.75 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Leg and Wheel Fairings | 9/11/2019 | 6 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings: 48-10 -> 48-12 | 11/11/2019 | 5.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings | 13/11/2019 | 3.5 | Halanda | Benedikovic | |
| PAINT/FURNISHING/UPHOLSTERY / FUSELAGE KIT | Carpets: Verifying the carpets fit and checking CG with some live weight in the baggage area 😀 I,ll have to cut out some openings for the heater outlets.. | 16/11/2019 | 0.75 | Halanda | Benedikovic | ||
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings: Works on the intersection fairings continue and we ran into a clearance issue with the upper intersection fairing and the ANDAIR gascollators on each side. We’ll have to sort that out later.. | 17/11/2019 | 1.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | 3D design for the Instrument: I positioned a piezzo buzzer (free dowload from Grabcad) behind the instrument panel. This one will work as a backup and will be connected to the original Vans stall switch. The other design involves an external VR by B&C. It’s not a 100% accurate model but it’s good enough to check if you have enough space behind the panel.. Lastly I needed to move 2 screw holes on the left Aerosport instrument panel insert to accommodate the EFIS’s nutplates. | 17/11/2019 | 6.25 | Halanda | Benedikovic | |
| ENHANCEMENTS | TOW BAR TAILCONE STORAGE | Tow Bar Mount in the tailcone: Mock-up of the Tow Bar Mount.. | 18/11/2019 | 4.75 | Halanda | Benedikovic | |
| ENHANCEMENTS | TOW BAR TAILCONE STORAGE | Tow Bar Mount: Fork holder finished -riveted, made of Carbon Fiber and reinforced with bracket. | 19/11/2019 | 5.25 | Halanda | Benedikovic | |
| ENHANCEMENTS | TOW BAR TAILCONE STORAGE | Tow Bar Mount finished: Inspired by PILATUS PC6! | 20/11/2019 | 2 | Halanda | Benedikovic | |
| INVENTORY | INVENTORY Milw. Scissors, Altn Door Spring, Rammount: The Alternate Air Door Spring is actually a C182 part nr. S2952-15 | 20/11/2019 | 0.25 | Halanda | Benedikovic | ||
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings | 21/11/2019 | 3.5 | Halanda | Benedikovic | |
| ENHANCEMENTS | MISC. | 12V plug & light push button: Installation of the 12V plug and baggage light push button. | 22/11/2019 | 5 | Halanda | Benedikovic | |
| ENHANCEMENTS / ELECTRICAL & AVIONICS | ACCESS/INSPECTION COVERS / EXTERNAL POWER CONNECTOR | Baggage Bulkhead Door & Ext PWR Plug: Installing the baggage bulkhead door holder and the External Power Plug is now connected to the structure to avoid unintended loss in the tailcone or even worse: flight controls blockage. | 25/11/2019 | 3.25 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings | 28/11/2019 | 3.5 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings | 30/11/2019 | 3 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings | 5/12/2019 | 4 | Halanda | Benedikovic | |
| WELCOME | Situation Overview | 11/12/2019 | 0.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Push Buttons & Indicators: Push Buttons & Indicators. Some of them will be readable only when backlit, that’s the idea. The push buttons can operate as discrete inputs for various systems (e.g. G3X touch to inhibit ESP-X or manually activate display Reversion).. There is a typo on the DSPL RERVERS button and I’ll have a new switch engraved. Push Buttons and indicators are high quality, made in Germany. Momentary or ON/OFF functions available. | 13/12/2019 | 1 | Halanda | ||
| FINISH KIT | 47 SPINNER & COWLING | 47-2 -> 47-3 Spinner Back Plate preparation, priming and assembly. 47-10 Works on Oil Door. | 28/12/2019 | 3.5 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47 Various works on the cowl. | 29/12/2019 | 2.25 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-10 Oil Door | 30/12/2019 | 2.5 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-10 Oil Door | 6/1/2020 | 2 | Halanda | Benedikovic | |
| FINISH KIT | 48 GEAR LEG & WHEEL FAIRINGS | (48) Intersection Fairings | 7/1/2020 | 3.75 | Halanda | Benedikovic | |
| INVENTORY | STRATUS USBs | 14/1/2020 | 0.1 | Halanda | STRATUS USBs | ||
| PAINT / FURNISHING / UPHOLSTERY | Installing forward Aerosport Interior Side Panels. | 16/1/2020 | 5.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS / ENHANCEMENTS | INTERIOR LIGHTS | A friend 3d printed a bracket to hold to mount the compass. Tailcon lighitng with 2 small individual LEDs installed. | 16/1/2020 | 2.25 | Halanda | Benedikovic | |
| ENHANCEMENTS | SUN SHIELDS | http://www.aviatorshop.eu/RV-10/2020/04/30/2012020-sun-shields/ | 20/1/2020 | 2.75 | Halanda | Benedikovic | |
| INVENTORY | ANDAIR CHECK VALVES for fuel tank breathers ANDAIR DV125 Drain Valves for fuel tanks to replace original Vans drain valves. | 21/1/2020 | 0.1 | Halanda | |||
| PAINT / FURNISHING / UPHOLSTERY | Trimming and attaching the rear Aerosport interior panels. | 22/1/2020 | 6 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | MISC | Installing the doors closed limit switches. Panasonic AZ7120CE | 26/1/2020 | 4.75 | Halanda | Benedikovic | |
| ENHANCEMENTS / FUSELAGE KIT | 38 Rudder Pedals & Brake System / BERINGER Brakes & Parking Brake | Filling the BERINGER brake system with RADCOLUB FR257 (MIL-PRF-87257) fluid. +looking for potential leaks -found 3 | 28/1/2020 | 2.5 | Halanda | Benedikovic | |
| FUSELAGE KIT | 43 CABIN TOP | Filler and sanding the front A pillars on cabin top to accommodate the front Aerosport side panels. | 31/1/2020 | 4.75 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Last trimming and attaching the forward Aerosport Interior Panels. | 2/2/2020 | 2.75 | Halanda | Benedikovic | ||
| ENHANCEMENTS | INTERIOR LIGHTS | Wheelen LED - Baggage Light -test performed | 3/2/2020 | 0.25 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Wet Compass blind riveted to the Center Cabin Brace (WD-1043) | 6/2/2020 | 0.5 | Halanda | Benedikovic | |
| INVENTORY | AMPLOC Hall Effect Current Sensors Headrests for rear seats | 7/2/2020 | 0.25 | Halanda | |||
| ENHANCEMENTS | MISC | Forward Harness Holder Brackets. These are being designed to hold the forward shoulder harnesses on top when not in use. | 11/2/2020 | 2.5 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Michal, (the upholstery specialist) is working on the forward seats. | 15/2/2020 | |||||
| ELECTRICAL & AVIONICS | MISC | Fabricating a removable contactor bracket for 2 contactors in the tailcone section. | 15/2/2020 | 3.1 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | INSTRUMENT PANEL | Relabeled the BACKUP switch into ESS to make it more obvious for pilots that this switch feeds the ESSENTIAL BUS and its components. So far, 3D model only. | 16/2/2020 | 0.5 | Halanda | ||
| PAINT / FURNISHING / UPHOLSTERY | Headrests for rear pax installed | 19/2/2020 | 2.75 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Interior Paint | 3/3/2020 | 5 | Halanda | Benedikovic | ||
| INVENTORY | STATIC WICKS DD-1W with B-4 BASE | 4/3/2020 | 0.1 | Halanda | |||
| PAINT / FURNISHING / UPHOLSTERY ENHANCEMENTS | PLANEAROUND DOOR LOCKING SYSTEM | Installing Door Sills from Aerosport and PlaneAround central door locking safety mecanism. | 4/3/2020 | 4.5 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Forward Seats Progress -Ready for testing.. | 13/3/2020 | |||||
| PAINT / FURNISHING / UPHOLSTERY | Fwd Gear Fork anodized | 15/3/2020 | 2 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Door Paint -Found some spots that had to be redone. | 16/3/2020 | 3.75 | Halanda | Benedikovic | ||
| INVENTORY | FWFD KIT Inventory + Engine and Prop | 20/3/2020 | 6.25 | Halanda | Benedikovic | ||
| INVENTORY | GIGAVAC Contactors GX11SA | 25/3/2020 | 0.1 | Halanda | Benedikovic | ||
| FIREWALL FORWARD | FF1-5 ENGINE INSTALLATION | Installing the IO540 | 26/3/2020 | 2.75 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Testing the seat foams | 26/3/2020 | 0.5 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Interior Paint (doors) | 28/3/2020 | 2 | Halanda | Benedikovic | ||
| FINISH KIT | 47 SPINNER & COWLING | (47) SPINNER & COWLING | 29/3/2020 | 4.5 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | (47) SPINNER & COWLING | 30/3/2020 | 4 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling | 31/3/2020 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling Modification on the bottom cowls -will use two fasteners per side. | 1/4/2020 | 2 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling | 2/4/2020 | 6.5 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling | 3/4/2020 | 3.5 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling | 4/4/2020 | 4 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling +starter removal for SALE! (sold) | 5/4/2020 | 3.75 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling Louvers were alodined. | 8/4/2020 | 5.75 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling | 10/4/2020 | 3.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | FF2-1 -> FF2-20 Starting works on the baffles. | 11/4/2020 | 2.1 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | FF2-1 -> FF2-20 | 12/4/2020 | 3.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | FF2-1 -> FF2-20 | 13/4/2020 | 5.25 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | FF2-1 -> FF2-20 | 14/4/2020 | 4.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | FF2-1 -> FF2-20 | 15/4/2020 | 3.75 | Halanda | Benedikovic | |
| INVENTORY | Flap handle came back from friend’s dad who made this perfect label on the handle to identify the switch function. I’ll put some clear coat on to protect the text.. Thank you Rastik! 😉 | 15/4/2020 | 0.1 | Halanda | FLAP HANDLE RECEIVED LABELED | ||
| FIREWALL FORWARD | FF2 COWLE BAFFLE | FF2-1 -> FF2-20 + left magneto removed FOR SALE! | 18/4/2020 | 3.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | FF2-1 -> FF2-20 Trimming horizontal pins and various adjustments.. | 19/4/2020 | 4.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF4 FUEL SYSTEM & FAB 540 AP | FAB (AIR BOX) | 22/4/2020 | 2.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF4 FUEL SYSTEM & FAB 540 AP | FAB (AIR BOX) | 23/4/2020 | 3 | Halanda | Benedikovic | |
| INVENTORY | AIR AVIONICS AT1 & SEAT LEATHER | 24/4/2020 | 0.2 | Halanda | AIR AVIONICS AT1 & SEAT LEATHER | ||
| FIREWALL FORWARD | FF4 FUEL SYSTEM & FAB 540 AP | FAB (AIR BOX) | 24/4/2020 | 2.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF4 FUEL SYSTEM & FAB 540 AP | FAB (AIR BOX) & Air Inlet | 25/4/2020 | 1.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | MISC | CONTACTORS INSTALLATION | 25/4/2020 | 2.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF4 FUEL SYSTEM & FAB 540 AP | Air Inlet in the cowling: | 26/4/2020 | 1.5 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | HARNESS COLOR: Looking for the right belts and harnesses color to complement the cockpit interior color. | 27/4/2020 | 0.5 | Halanda | |||
| ELECTRICAL & AVIONICS | 220V OIL PREHEAT SYSTEM | Installing the low profile IP65 rated 220V socket for the EZ-HEAT oil preheat system. Plug and socket feature a lockable system which can be connected and disconnect hot / under load. | 28/4/2020 | 0.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | AIR SEAL FABRIC | 29/4/2020 | 3.75 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | Screw fasteners instead of bottom cowl hinges. This mod will make removing and attaching the bottom cowl easier. +1 shot behind the bulkhead.. | 30/4/2020 | 1.5 | Halanda | Benedikovic | |
| FINISH KIT | 47 SPINNER & COWLING | 47-4->47-12 Cowling +poor man’s ‘LightBox’ | 30/4/2020 | 0.75 | Halanda | Benedikovic | |
| ENHANCEMENTS | ANDAIR Oil Separator | Position of the collector has changed for better access. Custom hoses added -might need to modify later with second alternator and oil filter adapter installed. | 4/5/2020 | 4.75 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Valve Covers Paint Removal | 6/5/2020 | 1 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | FF2 COWLE BAFFLE | Baffles alodined and Valve Covers Chrome-plated | 7/5/2020 | 4.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF4 FUEL SYSTEM & FAB 540 AP | Aluminium plated fixated below the air filter to avoid the air filter rubbing through the air box. | 9/5/2020 | 1.25 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF4 FUEL SYSTEM & FAB 540 AP | FAB modified to use an Automatic Alternate Air Door sytem. No pilot action required. | 13/5/2020 | 1.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF2 COWLE BAFFLE | (FF2-17) Tensions springs instead of tension rods. This section has been modified to use tension springs instead of tension rods. For easy of operation/removal/installation. | 13/5/2020 | 2.25 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF3 CONTROL CABLES | FF3 Installing Push/Pull Control Cables | 13/5/2020 | 1.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | MISC | New Contactor Holder Bracket | 16/5/2020 | 2.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD / ELECTRICAL & AVIONICS | FF5 OIL SYSTEM ELECTRICAL & AVIONICS | B&C Oil Filter Adapter, Starter & Alternators | 21/5/2020 | 2.25 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | SUREFLY Electronic Magneto | SUREFLY Electronic Magneto | 22/5/2020 | 1.25 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF4 FUEL SYSTEM, FF5 OIL SYSTEM | Oil & Fuel Hoses | 22/5/2020 | 2.75 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | External Power Connector, Antennas | Flarm Antenna, EXT PWR CB installed | 25/5/2020 | 2 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF6 EXHAUST SYSTEM, ELECTRICAL & AVIONICS | Spark Plugs Wiring & Exhaust installed | 28/5/2020 | 2.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | 47 SPINNER & COWLING | Cowling | 29/5/2020 | 4 | Halanda | Benedikovic | |
| FIREWALL FORWARD | 47 SPINNER & COWLING | COWLING | 30/5/2020 | 3.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF1 ENGINE INSTALLATION | PROP GOVERNOR INSTALLATION | 6/6/2020 | 2.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | 220V OIL PREHEAT SYSTEM | E-Z Heat Preheat Pads | 7/6/2020 | 3.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF3 CCONTROL CABLES | Control Cables installation | 8/6/2020 | 5.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD | 47 SPINNER & COWLING | Cowling | 9/6/2020 | 4.5 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF6 EXHAUST SYSTEM | FF6 EXHAUST SYSTEM | 10/6/2020 | 3.75 | Halanda | Benedikovic | |
| FIREWALL FORWARD | FF3 CCONTROL CABLES | FF3 Control Cables | 10/6/2020 | 3 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Artex 345 ELT installation | 11/6/2020 | 2.75 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Front Seats Upholstery in progress | 12/6/2020 | |||||
| FIREWALL FORWARD | 47 SPINNER & COWLING | COWLING | 13/6/2020 | 4 | Halanda | Benedikovic | |
| WINGS KIT | 24 WING TIP | Wingtip Light Lense | 15/6/2020 | 3 | Halanda | Benedikovic | |
| FIREWALL FORWARD | 47 SPINNER & COWLING | COWLING | 16/6/2020 | 4 | Halanda | Benedikovic | |
| INVENTORY | INVENTORY Pins & CO Detector | 25/6/2020 | 0.5 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Front Seats: lower part finished | 26/6/2020 | |||||
| ELECTRICAL & AVIONICS | Defog Fans | 27/6/2020 | 1.5 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Front Seats: Headset Hangers | 28/6/2020 | 2 | Halanda | Benedikovic | ||
| Overhead Console / System | Overhead panel | 28/6/2020 | 4.25 | Halanda | Benedikovic | ||
| FINISH KIT | 49 SEATS & SEAT BELTS | Front Seat Rails | 29/6/2020 | 1.75 | Halanda | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Headset Hangers & Aerosport Seat Handle | 29/6/2020 | 4 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Installing AT-1 Traffic & both Regulators | 3/7/2020 | 1.5 | Halanda | Benedikovic | |
| INVENTORY | INVENTORY: G5 GPS Antenna, Coup holders for rear seats, Magneto RPM sensor, Updated 75PSI Fuel Pressure Transducer | 11/7/2020 | 0.25 | Halanda | Benedikovic | ||
| Overhead Console / System, Interior Lights | Overhead Panel lights | 20/7/2020 | 3 | Halanda | Benedikovic | ||
| FIREWALL FORWARD ELECTRICAL & AVIONICS | FF4 FUEL SYSTEM | Engine Sensors: FT-60 (RED BOX) Fuel Flow Metering Unit, Fuel Press. Sensor, MAP Sensor, Oil Press Sensor | 26/7/2020 | 4.75 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Trim Motors Wiring: Using DTM connectors. | 31/7/2020 | 2.75 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Static Wicks installation & Ground Points | 5/8/2020 | 3.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Antennas | AT-1 Firewall Antenna PassThrough | 7/8/2020 | 1 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel MockUp: For Avionics Installation.. | 9/8/2020 | 5.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Trim Motors/Servos wiring: DTM connectors in use. | 10/8/2020 | 1.5 | Loy | Benedikovic | ||
| INVENTORY | INVENTORY Avionics | 14/8/2020 | 1 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS, PITOT STATIC SYSTEM | Instrument Panel | Air Connection to and via GSU25: AOA, Static and Total Pressure lines | 29/8/2020 | 2 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Key Switch Installation | 31/8/2020 | 0.25 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Wiring & Electrical | 5/9/2020 | 4.5 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Antennas | Electrical & Wiring (Antennas) | 6/9/2020 | 8 | Loy | Benedikovic | |
| PAINT / FURNISHING / UPHOLSTERY | Front Seats Upholstery: Front Seats Upholstery finished. | 10/9/2020 | Halanda | Benedikovic | |||
| SERVICE BULLETINS | Service Bulletin SB 18-03-30 | 14/9/2020 | 4 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Helping hands by Barbora -student from Faculty of Aeronautics | 18/9/2020 | 5 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Avionics Installation / Wiring | 19/9/2020 | 8 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Avionics Installation / Wiring | 27/9/2020 | 8.5 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Avionics Installation / Wiring | 7/10/2020 | 8 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Avionics Installation / Wiring | 10/10/2020 | 7.5 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Avionics Installation / Wiring | 14/10/2020 | 8 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel Inserts | 15/10/2020 | 3 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel Inserts | 21/10/2020 | 8 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel Inserts | 25/10/2020 | 8 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Avionics Installation / Wiring: DME connector KN63 and Alternator Connector replacement | 6/11/2020 | 2 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel | 11/11/2020 | 9 | Halanda | Benedikovic | |
| MISC | Covers & Plugs arrived | 20/11/2020 | 0.25 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | DME KN63 Connector Wiring | 5/12/2020 | 0.75 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel Inserts | 7/12/2020 | 8 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Electrical / Wiring / Avionics | 9/12/2020 | 8 | Loy | Benedikovic | ||
| FIREWALL FORWARD | FF6 EXHAUST SYSTEM | FF6-4 EXHAUST SYSTEM: Heating /Vent Scat | 9/12/2020 | 1 | Halanda | Benedikovic | |
| ENHANCEMENTS | 220V OIL PREHEAT SYSTEM | Oil Preheat System / Plug Cover: Designing the PreHeat Plug Cover | 13/12/2020 | 4.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | GMU11 MagnetoMeter Bracket | 14/12/2020 | 2.75 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Starter Engaged Warning Relay: Mounted on the firewall. | 15/12/2020 | 2.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Electrical / Wiring / Avionics | 18/12/2020 | 6 | Loy | Benedikovic | ||
| ENHANCEMENTS | PlaneAround Door Locking System | Planearound Door Locking System | 31/12/2020 | 4.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Electrical / Wiring / Avionics: Rocker Switches backlight wiring.. | 11/1/2021 | 5.75 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | OAT probe and Stall Warn installation | 12/1/2021 | 2.75 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Electrical / Wiring: Circuit Breaker Panel | 20/1/2021 | 7.75 | Loy, Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Electrical / Wiring: Flap Position Sensor, Ground Termination/Junction Boxes.. | 27/1/2021 | 8 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | External Power Connector | Electrical / Wiring: Wing root holes for connectors; Alternator 1 and Starter Wiring; Preheat System plug cover, Rudder Trim Switch wiring; Fuel Sensor Wiring, MASTER and ESS switches | 31/1/2021 | 7.5 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Electrical / Wiring: Annunciator Test Switch; Instrument Mockup Panel | 6/2/2021 | 6.75 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Electrical / Wiring Avionics: Wiring with predetermined wire lengths: | 10/2/2021 | 8.5 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Electrical / Wiring: Audio Wires; Avionics Wiring | 20/2/2021 | 9 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Interior Lights | Dome Light Timer: Dome Light Timer prototype | 9/3/2021 | 3 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | 220V OIL PREHEAT SYSTEM | Electrical / Wiring: Prewired cables go behind the panel.. Diode block; Wing Root Wiring; Amplock AMP meter | 10/3/2021 | 7.5 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Grip Wiring | 17/3/2021 | 6 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel Wiring | 25/3/2021 | 6.5 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Initial Avionics Startup: Initial Avionics startup. No faults | 26/3/2021 | 1 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | Avionics Setup: Setting up the sensors and limitations.. | 30/3/2021 | 4 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Database Updates | 3/4/2021 | 3 | Halanda | Benedikovic | ||
| Workshop, Transports | Trial Move out of the Workshop | 3/4/2021 | 0.5 | Benedikovic | |||
| ELECTRICAL & AVIONICS | Avionics Setup / Configuration: Audio Panel does not respond when configured to correct GMA345 model.. | 6/4/2021 | 4.5 | Halanda | Benedikovic | ||
| SERVICE BULLETINS | Service Bulletin SB-00002 | 12/4/2021 | 3.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Avionics / Wiring | 14/4/2021 | 8.75 | Loy | Benedikovic | ||
| ELECTRICAL & AVIONICS | Antennas | COM 2 Antenna | 14/4/2021 | 1.5 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS | Avionics Configuration | 16/4/2021 | 6 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Inventory: GNC 255 Backplate and DTM Connector | 20/4/2021 | 1 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Rear Seat Base Plate Construction | 24/4/2021 | 3.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Avionics / Wiring: Tailcone Wiring | 29/4/2021 | 3.75 | Loy | Benedikovic | ||
| FAB 540 AP, ENHANCEMENTS | Update of the Automatic Alternate Door | 29/4/2021 | 2 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | COM / NAV 2 Installation & Wiring Check | 29/4/2021 | 3 | Loy | Benedikovic | |
| ELECTRICAL & AVIONICS, Workshop, Transports, 44 Wing Attachement | Moving to the hangar & Wings installation: Electrical / Avionics Guru/Maestro Jaro Loy on picture. | 29/4/2021 | 1 | ||||
| ELECTRICAL & AVIONICS | Exterior Lights | Landing Light & Pos. Lts Test | 30/4/2021 | 0.5 | Loy | Benedikovic | |
| ENHANCEMENTS | Center Console, ANDAIR Fuel System | Center Console with Fuel Selector | 1/5/2021 | 2 | Halanda | Benedikovic | |
| ENHANCEMENTS | ANDAIR Fuel System | Fuel Tank Alternate Air Valve: Check Valve from Andair installed. Opens automatically when the fuel intace becomes blocked to prevent fuel tank collapse. | 1/5/2021 | 1.5 | Halanda | Benedikovic | |
| EMPENNAGE KIT | 9 Elevators | Elevator Installation | 3/5/2021 | 1.75 | Halanda | Benedikovic | |
| BUILDER'S LOGBOOK | CAA Visit | 4/5/2021 | |||||
| ELECTRICAL & AVIONICS | Instrument Panel | Instrument Panel Inserts: Custom made insert with description (Left Panel) | 5/5/2021 | ||||
| EMPENNAGE KIT | 7 Rudder, 12 Empenage Fairings | Rudder & Empenage Fairings | 6/5/2021 | 3.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS FIREWALL, FORWARD, FINISH KIT | 27 Firewall, Instrument Panel, 50 Cabin Heat & Ventilation, FF5 OIL SYSTEM | Push&Pull Controls final installation: Rear Heat, Front Heat, Parking Brake, Oil Cooler Door | 12/5/2021 | 3 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Wiring Tailcone & Overhead Panel | 14/5/2021 | 6 | Loy | Benedikovic | ||
| FUSELAGE KIT | 43 Cabin Cover | Tailcone Fwd Top Skin | 16/5/2021 | 3.5 | Halanda | Benedikovic | |
| WINGS KIT | 22 Flaps | Flaps Install | 18/5/2021 | 4 | Halanda | Benedikovic | |
| FUSELAGE KIT | 35 Access Covers and Floor Panels | 35-9 Mid Cabin Side Covers | 21/5/2021 | 2.25 | Halanda | Benedikovic | |
| First Refueling: Preparation for initial engine start. | 29/5/2021 | 0.5 | Halanda | Benedikovic | |||
| 1st Engine Start: Maestro himself before we pulled the RV-10 out of the hangar for the 1st engine start: | 30/5/2021 | 2 | Halanda | Benedikovic | |||
| ENHANCEMENTS, WINGS KIT | 18 Fuel Tank, ANDAIR Fuel System | Fuel Breather Line | 1/6/2021 | 2 | Halanda | Benedikovic | |
| ENHANCEMENTS, PAINT / FURNISHING / UPHOLSTERY | Center Console | Armrest Installation | 2/6/2021 | 0.25 | Halanda | Benedikovic | |
| FINAL PREPARATIONS | Covers & Final Exterior Scan | 5/6/2021 | 0.5 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Rear Seat Bank finished | 9/6/2021 | |||||
| ENHANCEMENTS | Panel Inserts & Decals: Graphics & Final Products.. | 10/6/2021 | 5.75 | Halanda | Benedikovic | ||
| FINAL PREPARATIONS | Flight Controls Lock: Initial design seems to work well except ailerons / flaps lock. We run into the danger of damage when selecting flaps above 15deg with the lock installed. Ailerons + Wing Tip makes more sense but the discharger is in the way – we will think it over.. Rudder & Elevator lock works very well. | 11/6/2021 | 5.5 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | G5 Static+Total Pressure Connections: Instrument Panel almost finished | 12/6/2021 | 7.75 | Halanda | Benedikovic | |
| Welcome | Sun Shades: Sun Shades installed. | 18/6/2021 | 3 | Halanda | Benedikovic | ||
| FINAL PREPARATIONS | Initial Weighting: still paintless.. | 24/6/2021 | 3 | Halanda | Benedikovic | ||
| INVENTORY | Rudder Trim Springs Inventory | 24/6/2021 | 0.5 | Halanda | |||
| PAINT / FURNISHING / UPHOLSTERY | Rear Seat installed & brought to trial | 4/7/2021 | 1 | Halanda | Benedikovic | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Com / Nav 2 installed: GNC255 | 3/8/2021 | 0.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS / FUSELAGE KIT | Instrument Panel, 39 Control System | Grip Sticks installed | 25/8/2021 | 3.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Instrument Panel | SMART GLIDE push button: Optional SMART GLIDE momentary push button. | 16/9/2021 | 1 | Halanda | ||
| ELECTRICAL & AVIONICS | Instrument Panel | Right Instrument Panel with Labels installed | 9/9/2021 | 2.5 | Halanda | Benedikovic | |
| ELECTRICAL & AVIONICS | Roll Servo has failed. Pulled out for replacement.. | 2/10/2021 | 0.75 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Front Seat Belts & Shoulder Harness | 2/10/2021 | 1.25 | Halanda | Benedikovic | ||
| Misc | Interior Door Handle | 3/10/2021 | 1 | Halanda | Benedikovic | ||
| PITOT STATIC SYSTEM | Pitot Static Leak Test | 4/10/2021 | 2.5 | Benedikovic | |||
| PAINT / FURNISHING / UPHOLSTERY | Rear Headrests installed | 6/10/2021 | 0.5 | Halanda | Benedikovic | ||
| PAINT / FURNISHING / UPHOLSTERY | Glareshield Edge Protection extended | 3/11/2021 | 0.25 | Halanda | Benedikovic | ||
| Antennas | Antennas check | 10/11/2021 | 3.75 | Halanda | Benedikovic | ||
| Welcome | SPECIAL AIRWORTHINESS CERTIFICATE issued | 18/11/2021 | |||||