7 Rudder

6.5.2021 Rudder & Empenage Fairings

supikLeave a comment

Rudder: FINISHED

supikLeave a comment

2015-12-28

The Rudder is FINISHED! Counter weight installed, skins bended and riveted. Now it has to rest with the trailing edge sealed.. Both rudder fairings have been pop-riveted in place (Section 12: EMPENNAGE FAIRINGS).

Rudder: progress picture

supikLeave a comment

2015-12-27

Tommorrow we hope to finish the Rudder

Rudder: started works today

supikLeave a comment

Today we decided to start with the rudder section. Ribs, shear clips & stiffeners separated and trimmed and deburred. All surfaces were primed to prevent corrosion.

Add Cold Air Vents insect mesh / screen protection + NORMAL Fuel Breathers & Negative Pressure Safety Relief Valve
MAG METER Engine Run Up TEST / VIB TEST
Glareshield handle covers
Wiring Manual Update
-Isolate Dome Light
Update Dome light Box
Adjust Elev Rear Stop
AMM Update
1. Air Filter K&N PN E-3450 or TEMPEST AA10-3450
2. Nose gear Mooney dampers check for play
3. Check MASTER -> ESS Diode
4. Main Battery, 6years limit or load test pass every annual after passing 6years
Check Idle Mixture Setup after 1st XX? hrs
Right Panel:

Placard Night/IFR or to refer to their
being listed in the AFM

CBs rename
GAD29 / ARINC
GEA24 / EIS (Engine Information System)
GAD27 / ECS (Electrical Control System)
COMPSS / P/B LTS
OVHD AIR / MAP LTS (swap to 2 AMP C/B - check MAP LTS wiring)
AVIONX / E. BUS
AVIONX / M. BUS
KEEP AL. / BUS
ELEV / TRIM

Push buttons:
P/B LTS TEST - push test
MFD REVERSION - MFD REVERS - push reversion
TERRAIN ALERTS - TERR OFF - push off

mom p/b: EVENT MARKER

Popisky pre ALT-1 a ALT-2 regler, Brake Reservoir

Add DME label on GMA345

4.5 - 18mm
PILOT a COPI v stredovej konzole

Inner side of entry doors -plug holes
Sticker 15mm

Inner side of doors: OPEN CLOSE modify

Pedestal info graphics

Engine Preheat 230V Placard
Reseal OVHD Panel Covers. Rear Pax Ovhd panel -vibrations (cables air vents?)
Koberce
Replace L & Center Insert Labels
Garmin Service Bulletin 23038
Roll Servo affected SN 6N7002069

https://support.garmin.com/en-US/aviation/faq/fDr3LoWvVh73y7YNV5WnjA/
Prop cycling effective from 2150 RPM (min RPM with full aft prop lever setting: 1900 RPM)
Adjust Bowden Cable in Throttle Quadrant
order TEMPEST AIR FILTER: AA10-3450
-vhodne miesto na palubne LED EMER svetlo?
-drziak 3D
HOT BUS Cover / Protection
Add 1 center flood light in Ovhd Panel
S/B List
Move Backup Stall Warning from behind DME panel
Heater Pwr Plug, drill drain hole
Low Pitch The low pitch setting in a -1 and -4 system sets the minimum blade angle the propeller can achieve. It is a physical stop which is externally adjustable; consult the appropriate propeller owners manual for adjustment procedure.
d) Hartzell recommends selecting a setting for naturally aspirated engines wherein the static RPM is at least 25-50 RPM less than the maximum rated RPM of the engine. 1 Ensure that this is not being masked by the governor setting. Refer to the appropriate governor manual and the "Governor" section in the Accessories chapter of this manual.
Static WOT RPM: 2670
https://youtu.be/yq7cuDJJCXQ?si=sq-RnvuHEvxBTF6f
AILERON TRIM - Inspect for asymmetrical trim force Left vs. Right
Prop Reclocking? 60deg with #1 at TDC
Avanza AP Setup!

Auto pilot setup pitch. This works for me.
pitch servo torque 50 %
pitch servo gain 0.65
min air speed limit 65 kt
max air speed limit 200 kt
vertical speed gain 0.45
vertical accel gain 0.5
air speed gain 0.5
Task Card for Cruise Perf
Wireles Avionics Interconnect
Traffic - Block Garmin Voice
Vyber ciernu kozu z pnnelov pilot / copi
sicherfarba na zavesy/srouby
torque seal - engine side, control cable nuts
otoc p/b cover 90deg (pruzina hore)
1. Spodna cast kapoty predlzit otvor na nohu a vyrobit prekryt
2. Baffles - spodna cast kabiny / air inlets

RV-10 LOGBOOK ( *Stavebný denník* ) OM-ELA S/N 41519 staviteľ: Halanda - dozor: Benedikovič

KIT	Section	Page complete / memo	Date	Hours	Completed	Verified	CAA entry / memo
				2576.4	TOTAL Project Hours
				2138.9	TOTAL Project Hours
EMPENNAGE		Unboxing / Inventory	04/12/2015	8.5	Halanda
EMPENNAGE	6 Vertical Stabilizer	6-2 -> 6-3 (incl. dimpling, deburring and test assy)	05/12/2015	6.5	Halanda	Benedikovic
EMPENNAGE	6 Vertical Stabilizer	6-4 -> 6-5 (incl. priming)	06/12/2015	7.2	Halanda	Benedikovic
EMPENNAGE	6 Vertical Stabilizer	6-5	07/12/2015	8.5	Halanda	Benedikovic
EMPENNAGE	6 Vertical Stabilizer	6-5 -> 6-6 finished	08/12/2015	7.5	Halanda	Benedikovic
EMPENNAGE	10 Tailcone	10.2 -> 10.4 general alignment of parts, deburring, priming	08/12/2015	2.5	Halanda	Benedikovic
EMPENNAGE	10 Tailcone	10.3 -> 10.5 bulkhead assembly-riveting	09/12/2015	9	Halanda	Benedikovic
EMPENNAGE	10 Tailcone	10.7 -> 10.9 priming & riveting	10/12/2015	9.5	Halanda	Benedikovic
EMPENNAGE	10 Tailcone	10.7 Riveting the side-walls to stringers & bulkheads	11/12/2015	6.7	Halanda	Benedikovic
EMPENNAGE	10 Tailcone	10.0 -> 10.11 Deburring, Priming and Riveting the AFT Deck	12/12/2015	4.5	Halanda	Benedikovic
EMPENNAGE	10 Tailcone	Test-Fitting the upper skins	13/12/2015	1	Halanda	Benedikovic
TOOLS			15/12/2015	0.5	Halanda		Replaced compressor, oil change & filter cleaned
							15/12/2015 Inspected by The Transport Authority of Slovak Republic
EMPENNAGE	10 Tailcone	10.12 -> 10.26 Bolting the shoulder harness Anchores, Attaching the battery mount, bolting the elev. bellcrank, riveting the upper skin	17/12/2015	8	Halanda	Benedikovic
EMPENNAGE	11 Empennage Attach	11.6, 11.8 -> 11.9 Assembling & priming the elev. pushrod, manufacturing & priming of the elev. trim parts	17/12/2015	2.3	Halanda	Benedikovic
EMPENNAGE	7 Rudder	7.2 -> 7.3 Started works on the Rudder. Ribs, Stiffeners & Shear clips separated, deburred & primed.	20/12/2015	3.5	Halanda	Benedikovic
EMPENNAGE	7 Rudder	7.4 -> 7.6	21/12/2015	5	Halanda	Benedikovic
EMPENNAGE	7 Rudder	7.6 -> 7.8	22/12/2015	6.5	Halanda	Benedikovic
EMPENNAGE	7 Rudder	7.9 -> 7.10	27/12/2015	8	Halanda	Benedikovic
EMPENNAGE	7 Rudder	7.11 -> 7.12 Rudder finished. Added counterweights, skins bended.	28/12/2015	9	Halanda	Benedikovic
EMPENNAGE	12 Empennage Fairings	12.2 -> 12.3 Rudder Fairings -finished	28/12/2015	1.5	Halanda	Benedikovic
EMPENNAGE	8 Horizontal Stabilizer	8.2 -> 8.7	1/1/2016	9.5	Halanda	Benedikovic
EMPENNAGE	8 Horizontal Stabilizer	8.8 Testfitting	3/1/2016	4.5	Halanda	Benedikovic
EMPENNAGE	8 Horizontal Stabilizer	8.8 -> 8.10 Dimpling, Deburring and Priming	4/1/2016	7	Halanda	Benedikovic
EMPENNAGE	8 Horizontal Stabilizer	8.11 -> 8.12 Riveting the front spars to the skin and inspar ribs to the front spar assy	5/1/2016	5.5	Halanda	Benedikovic
EMPENNAGE	8 Horizontal Stabilizer	8.11 -> 8.13 Riveting..	6/1/2016	8.5	Halanda	Benedikovic
EMPENNAGE	8 Horizontal Stabilizer	8.11 -> 8.13 Riveting..	7/1/2016	5.2	Halanda	Benedikovic
EMPENNAGE	8 Horizontal Stabilizer	..8.14 FINISHED	8/1/2016	6.5	Halanda	Benedikovic
Enhancements	LNDG Lights	Install KIT received, examined and inventored	9/1/2016	0.5	Halanda	Benedikovic
EMPENNAGE	9 Elevators	9-2, 9-5 Separating Elevator Ribs, drilling, separating Shear Clips..	10/1/2016	6	Halanda	Benedikovic
EMPENNAGE	9 Elevators	9-2 -> 9-5 Deburring, dimpling, priming. Riveting of the half ribs & rear spar.	11/1/2016	7.5	Halanda	Benedikovic
EMPENNAGE	9 Elevators	9-5 -> 9-6	13/1/2016	8.5	Halanda	Benedikovic
EMPENNAGE	9 Elevators	9-6 -> 9-10	14/1/2016	5	Halanda	Benedikovic
EMPENNAGE	9 Elevators	9-10 -> 9-13	17/1/2016	7	Halanda	Benedikovic
EMPENNAGE	9 Elevators	9-13 -> 9-15	18/1/2016	5	Halanda	Benedikovic
EMPENNAGE	9 Elevators	2nd Elevaror: 9-2, 9-5 Separating Elevator Ribs, drilling, separating Shear Clips..	19/1/2016	8	Halanda	Benedikovic
EMPENNAGE	9 Elevators	Trim Tabs attached	14/3/2016	7.5	Halanda	Benedikovic
WINGS		Unboxing / Inventory	15/3/2016	9.5	Halanda
WINGS		Unboxing / Inventory	17/3/2016	5.3	Halanda
EMPENNAGE	9 Elevators	9-18 -> 9-19 Trim Tab Hinge (Elevators Finished)	18/3/2016	3.5	Halanda	Benedikovic
WINGS	18 Fuel Tank	Test assembly	19/3/2016	8.6	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-2 -> 18-4 Dimpling, deburring, countersinking (general preparation of L tank for sealing	20/3/2016	7.8	Halanda	Benedikovic
TOOLS			20/3/2016		Halanda		Angle Grinder added to tools/equipment
WINGS	18 Fuel Tank	18-2 -> 18-4	23/3/2016	6.7	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-2 -> 18-5	24/3/2016	7	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-2 -> 18-5	25/3/2016	8	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-2 -> 18-5	27/3/2016	6	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-2 -> 18-5	29/3/2016	7.5	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-2 -> 18-5 Sealing Ribs; let it dry for almost 2 days	03/4/2016	6.3	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-2 -> 18-5 Riveting ribs in the fuel tank	05/4/2016	9	Halanda	Benedikovic
WINGS	21 Aileron	21-2	07/4/2016	8	Halanda	Benedikovic
WINGS	21 Aileron	21-2->21-4	08/4/2016	8.5	Halanda	Benedikovic
WINGS	21 Aileron	21-2->21-4	09/4/2016	7.3	Halanda	Benedikovic
							12/05/2016 Inspected by The Transport Authority of Slovak Republic
WINGS	21 Aileron	21-5->21-9	12/5/2016	9.6	Halanda	Benedikovic
WINGS	21 Aileron	21-5->21-9 Ailerons finished	14/5/2016	8	Halanda	Benedikovic
WINGS	18 Fuel Tank	1st leak test	18/5/2016	3.5	Halanda	Benedikovic	1st leak test with colored water successful! Both fuel tanks passed.
WINGS	18 Fuel Tank	18-4, 18-6 -> 18-8 Rear wall closed / sealed & clecoed	19/5/2016	5.6	Halanda	Benedikovic
WINGS	22 Flap	22-2 -> 22-4 Deburred edges, ribs trimmed	20/5/2016	7.5	Halanda	Benedikovic
WINGS	18 Fuel Tank	18-4, 18-6 -> 18-8 Rear wall riveted	21/5/2016	8.9	Halanda	Benedikovic
WINGS	22 Flap	22-4 -> 22-9 Ribs & Subassemblies attached. Spar, trailing edge and skins dimpled	22/5/2016	10.5	Halanda	Benedikovic
WINGS	22 Flap	22-4 -> 22-9 Ribs & Subassemblies attached. Trailing edge pro-sealed and clecoed for overnight.	23/5/2016	10.6	Halanda	Benedikovic
WINGS	22 Flap	22-4 -> 22-9 Trailing Edge riveted	24/5/2016	5.8	Halanda	Benedikovic
WINGS	18 Fuel Tank	Balloon leak test	4/6/2016	0.5	Halanda	Benedikovic	Successful balloon leak test on 'L' fuel tank.
WINGS	18 Fuel Tank	Balloon leak test	5/6/2016	0.5	Halanda	Benedikovic	'R' tank balloon bursted overnight, replaced in the morning
WINGS	18 Fuel Tank	Balloon leak test	6/6/2016	0.2	Halanda	Benedikovic	'R' tank balloon leak test successful after 24hrs
WINGS	17 Outboard Leading Edge	17-2 -> 17-4 Assembly, Deburring, Dimpling of skins and ribs.	6/6/2016	8.5	Halanda	Benedikovic
WINGS	17 Outboard Leading Edge	17-2 -> 17-4 Preparation / Priming	7/6/2016	10.5	Halanda	Benedikovic
WINGS	17 Outboard Leading Edge	17-2 -> 17-4 Preparation / Priming	8/6/2016	11	Halanda	Benedikovic
WINGS	17 Outboard Leading Edge	17-2 -> 17-4 Riveting of outboard ribs, cutting of the 'servie door'	9/6/2016	11	Halanda	Benedikovic
WINGS	17 Outboard Leading Edge	17-2 -> 17-4 Re-Assembly / glecoing for final riveting	10/6/2016	3.5	Halanda	Benedikovic
WINGS	17 Outboard Leading Edge	17-2 -> 17-4 Final riveting	11/6/2016	7.5	Halanda	Benedikovic
WINGS	13 Main Spar	Surface control & deburring	15/8/2016	6.5	Halanda	Benedikovic
WINGS	13 Main Spar	13-1 -> 13-5 preparation & priming parts	16/8/2016	8	Halanda	Benedikovic
WINGS	13 Main Spar	13-1 -> 13-5 Web extension installation, countersinking	18/8/2016	6.5	Halanda	Benedikovic
WINGS	13 Main Spar	13-1 -> 13-5 Nutplate install	19/8/2016	9	Halanda	Benedikovic
WINGS	13 Main Spar	13-1 -> 13-5 Tie down bracket & aileron bracket install, predrilling	21/8/2016	7	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-1 -> 14-6 Deburring edges	22/8/2016	10	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-1 -> 14-6 Deburring edges, shaping	23/8/2016	10	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-1 -> 14-6 Applying primer on wing ribs, pre-attachement with clecos	25/8/2016	8.8	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-1 -> 14-6 Riveting Flap Hinge Assemblies and Torque tube support bracket	26/8/2016	9.5	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-1 -> 14-6 Riveting Flaps to main spar	05/9/2016	5.5	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-1 -> 14-6 Riveting Flaps to main spar	06/9/2016	6.5	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-1 -> 14-6 various	06/9/2016	7	Halanda	Benedikovic
WINGS	14 Wing Ribs	14-6 Bolts installation	07/9/2016	3.5	Halanda	Benedikovic
WINGS	15 Rear Spar	15-1 -> 15-4 Deburring, preparation	10/9/2016	9.5	Halanda	Benedikovic
WINGS	15 Rear Spar	15-1 -> 15-4 Deburring, preparation & priming of parts	11/9/2016	10.5	Halanda	Benedikovic
WINGS	15 Rear Spar	15-2 Aileron bracket assy finished, pushrod hole copied	12/9/2016	8	Halanda	Benedikovic
WINGS	15 Rear Spar	15-4 Final assembly / riveting	13/9/2016	8	Halanda	Benedikovic
WINGS	15 Rear Spar	15-4 Final assembly / riveting	14/9/2016	5.5	Halanda	Benedikovic
WINGS	16 Top Wing Skins	16-1 -> 16-4 Deburring, Dimpling	18/9/2016	7.5	Halanda	Benedikovic
WINGS	16 Top Wing Skins	16-1 -> 16-4 Deburring, Dimpling	19/9/2016	9.5	Halanda	Benedikovic
WINGS	16 Top Wing Skins	16-1 -> 16-4 Priming	20/9/2016	4.5	Halanda	Benedikovic
WINGS	SB 16-03-28	Unboxing / Inventory	24/9/2016	0.5	Halanda	Benedikovic	Van's Service Bulletin SB 16-03-28 arrived
		Transport	28/9/2016	8	Halanda		Moving Tailcone, Fin and Stab to a new location to free up some space..
WINGS	SB 16-03-28	Disassembly of the old brackets to extract the original bearings. Deburring, priming, painting, assembly & riveting.	25/10/2016	9.25	Halanda	Benedikovic	Van's Service Bulletin SB 16-03-28 APPLIED
WINGS	20 BOTTOM WING SKINS	20-4 Preparation and installation of GAP FAIRINGS incl. Stiffeners	26/10/2016	8.5	Halanda	Benedikovic
WINGS	16 Top Wing Skins	16-3 Preparation and riveting of the top skin (L Wing)	27/10/2016	6.7	Halanda	Benedikovic
ELECTRIC AILERON TRIM	OP-38	OP38-2 -> OP38-4 preparation of parts, deburring, priming and assembly	27/10/2016	4	Halanda	Benedikovic
WINGS	20 BOTTOM WING SKINS	20-5 Deburring, dimpling & priming of bottom skins. Attaching fasteners	28/10/2016	5	Halanda	Benedikovic
WINGS	20 BOTTOM WING SKINS	20-5 Deburring, dimpling of Access plates	30/10/2016	2	Halanda	Benedikovic
ELECTRICAL	Corrugated Conduit		09/11/2016		Halanda		Purchase of 12m
WINGS	Rivets	Inventory of missing rivets	21/11/2016	0.1	Halanda		Added & inventory of missing rivets: 120 and 100pcs respectively
Enhancements	Wing LNDG lights	Cutouts in R leading edges	09/12/2016	4.5	Halanda	Benedikovic
Enhancements	Wing LNDG lights	Cutouts in L leading edges; LNDG Brackets installation	10/12/2016	8.5	Halanda	Benedikovic
WINGS	16 TOP WING SKINS	16-3 Riveting the top wing skins (missing row with AN426AD3-4	10/12/2016	1.2	Halanda	Benedikovic
WINGS	17 OUTBOARD LEADING EDGE	17-4 L & R outboard leading edges riveted to main spar assy	11/12/2016	5.5	Halanda	Benedikovic
		Purchase of wood for the wing cart	12/12/2016	3	Halanda
		Wing cart assembly	12/12/2016	5.75	Halanda		Credit for the idea and plans goes to Mouser! We have used your plans with light modifications. THANK YOU
WINGS	18 FUEL TANKS	Priming	12/12/2016	1.75	Halanda	Benedikovic
WINGS	18 FUEL TANKS	Attaching Fuel tanks to main spar assy.	13/12/2016	4.5	Halanda	Benedikovic	Tanks had to be removed twice due to overlaping skins.. Very tight fitment.
							15/12/2016 Inspected by The Transport Authority of Slovak Republic
WINGS	23 Aileron Actuation	Preparation, shortening the pushrods to required length, drilling, riveting and priming the parts.	03/03/2017	9.5	Halanda	Benedikovic
WINGS	23 Aileron Actuation	Installation	04/03/2017	2	Halanda	Benedikovic
PITOT STATIC SYSTEM	PITOT STATIC SYSTEM	Preparation, drilling. Ready for final assembly	05/03/2017	7.5	Halanda	Benedikovic
PITOT STATIC SYSTEM	Static ports, hardware and tube	Inventory	06/03/2017	0.1	Halanda		Inventory CLEVELAND T. Static KIT
ELECTRICAL & AVIONICS	VOR/ILS RAMI Antenna	Inventory	06/03/2017	0.1	Halanda		Inventory RAMI AV-520
TRANSPORTS & PAINTJOB		Transport of assembled parts and preparation of new workshop	26/11/2017	11.5	Benedikovic		Moving tailcone and wings to new workshop.
ELECTRICAL & AVIONICS	VOR/ILS Antenna	Preparation & Installation	01/12/2017	5	Halanda	Benedikovic
PITOT STATIC SYSTEM	PITOT STATIC SYSTEM	Prime & Installation	01/12/2017	0.5	Halanda	Benedikovic
PITOT STATIC SYSTEM	Static ports Installation	Installation and bonding with Araldite 420	05/12/2017	2.3	Halanda	Benedikovic
ELECTRIC AILERON TRIM	OP-38 Electric Aileron Trim to Access Door Attach	OP38-2 -> OP38-4 Attaching the trim unit to Wing Access Door	05/12/2017	0.5	Halanda	Benedikovic
EMPENNAGE	11 Empenage Attach	11-4 Fabricating and attaching shims	19/12/2017	3	Halanda	Benedikovic
Enhancements	Wing LNDG lights	Installation of the Light holders/frame and plexi glass	31/01/2018	8	Halanda	Benedikovic
EMPENNAGE	11 Empenage Attach	11-4, 11-5 Attaching and match drilling the horizontal stabilizer to empennage	02/02/2018	8.5	Halanda	Benedikovic
EMPENNAGE	11 Empenage Attach	Closing the inner side of the VS Tip Fairing & fine tuning its leading edge with micro balloons	06/02/2018	3	Halanda	Benedikovic
EMPENNAGE	11 Empenage Attach	Closing the inner side of the VS Tip Fairing & fine tuning its leading edge with micro balloons	07/02/2018	1	Halanda	Benedikovic
EMPENNAGE	11 Empenage Attach	11-6 Pushrod Assembly	07/02/2018	2	Halanda	Benedikovic
Enhancements	BERINGER Brakes	Arrival, Inventory, Pre-assembly	09/02/2018	3	Halanda	Benedikovic
Enhancements	LANDING LIGHTS	Inventory & function test	26/02/2018	0.5	Halanda	Benedikovic
FUSELAGE KIT		Inventory	05/03/2018	9	Benedikovic		Kit Inventory
FUSELAGE KIT		Inventory	06/03/2018	8.5	Benedikovic		Kit Inventory
FUSELAGE KIT	25 MID FUSE BULKHEADS	25-2 -> 25-5 Basic preparation, priming, riveting..	07/03/2018	8	Halanda	Benedikovic
FUSELAGE KIT	25 MID FUSE BULKHEADS	25-5 -> 25-8 BOLTING THE AFT BULKHEAD TOGETHER; REAR SPAR BULKHEAD ASSEMBLY; FUSELAGE BULKHEAD ASSEMBLY	08/03/2018	9.5	Halanda	Benedikovic
FUSELAGE KIT	25 MID FUSE BULKHEADS	25-5 -> 25-8 BOLTING THE AFT BULKHEAD TOGETHER; REAR SPAR BULKHEAD ASSEMBLY; FUSELAGE BULKHEAD ASSEMBLY	09/03/2018	8.7	Halanda	Benedikovic
FUSELAGE KIT	25 MID FUSE BULKHEADS	25-7 -> 25-8 Drilling, Deburring, Priming, Riveting the REAR SPAR BULKHEAD ASSEMBLY & FUSELAGE BULKHEAD ASSEMBLY	13/03/2018	8.5	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-2 -> 26-4 Procedure according plans	14/03/2018	6.8	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-2 -> 26-4 Procedure according plans	15/03/2018	4.75	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-2 -> 26-4 ATTACHING SEAT RIB SUBASSEMBLIES TO THE AFT CENTER SECTION BULKHEAD SUBASSEMBLY	16/03/2018	8.5	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-2 -> 26-4 Preparation of rear spar bulkhead ribs	17/03/2018	7.5	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-2 -> 26-4 RIB ATTACH TO REAR SPAR BULKHEAD	18/03/2018	9	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-5 -> 26-6 RIB TO FUSELAGE BULKHEAD ATTACH	19/03/2018	9	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-7 -> 26-8 BOTTOM SKINS - Dimpling, Deburring, Priming +glecoed to ribs	20/03/2018	6.5	Halanda	Benedikovic
Enhancements	STEP MOUNT	Fabrication, Priming, Drilling & Riveting the additional support bracket	26/03/2018	3	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-7 -> 26-8 BOTTOM SKINS -glecoed to ribs	26/03/2018	1	Halanda	Benedikovic
FUSELAGE KIT	27 FIREWALL	27-2 BULKHEAD ASSEMBLY -preparation, drilling, deburring, priming, riveting	27/03/2018	7.5	Halanda	Benedikovic
FUSELAGE KIT	27 FIREWALL	27-2 BULKHEAD ASSEMBLY -preparation, drilling, deburring, priming, riveting	28/03/2018	2	Halanda	Benedikovic
FUSELAGE KIT	26 MID FUSE RIBS & BOTTOM SKINS	26-7 -> 26-8 BOTTOM SKINS rivetiting	29/03/2018	4.5	Benedikovic Jr. & son Misko	Benedikovic
FUSELAGE KIT	27 FIREWALL	27-2 -> 27-5 works according plans	30/03/2018	8	Halanda	Benedikovic
FUSELAGE KIT	27 FIREWALL	27-2 -> 27-5 works according plans	01/04/2018	7.5	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN	28-4 DRILL AND TRIM CONTROL COLUMN MOUNT	04/04/2018	3	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN	28-2 -> 28-6 DRILLING, DEBURRING, PRIMING & ASSEMBLY WITH CLECOS	05/04/2018	7.75	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN	28-5 FINAL DRILL BOTTOM SKIN, MATCH-DRILL CONTROL COLUMN MOUNT	06/04/2018	4.5	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN	28-5 Priming FUSE FLOOR RIBS & various parts, Dimpling FWD BOTTOM SKIN	09/04/2018	5.5	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN, 27 FIREWALL	28-5, 28-6, 28-8, 28-11, 27-6 (HI LOKs used instead of regular rivets) Procedure according Constr. Plans	11/04/2018	7.5	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN	28-9 MATE MID FUSELAGE ASSEMBLY TO FORWARD FUSELAGE ASSEMBLY + SKIN OVERLAP (CLECOED)	13/04/2018	3.5	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN	28-9 MATE MID FUSELAGE ASSEMBLY TO FORWARD FUSELAGE ASSEMBLY. F-1004K-L & R Center Section Side Plates (primed, clecoed & partially riveted)	15/04/2018	4.5	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS, BHDS & BOTTOM SKIN	28-16 -> 28-17 DRILLING THE LANDING GEAR MOUNT	18/04/2018	3.75	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	29-2 -> 29-4 Fabricating BENDING & CLAMPING BLOCKS + Bending LONGERONS	19/04/2018	7.25	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	29-4 -> 29-5	20/04/2018	8	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	29-5 -> 29-10	21/04/2018	7	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	29-5 -> 29-10	22/04/2018	4	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	29-5 -> 29-10	25/04/2018	7.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Received SWITCH GUARDS & PIEZOELECTRIC BUZZER (Stall Warning)	29/04/2018	0.5	Halanda		Inventory
FUSELAGE KIT	29 FUSE SIDE SKINS	29-12 -> 29-14 per plans	01/05/2018	7.5	Halanda	Benedikovic
FUSELAGE KIT	27 FIREWALL	Problem discovered: rivets out of spec	03/05/2018	0.5	Halanda	Benedikovic
FUSELAGE KIT	38 RUDDER PEDALS & BRAKE SYSTEM	38-2 Creating Brake Pedals	03/05/2018	3	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	29-19 Vent Doors: Cutting brackets and slides apart; Assembling the doors; Priming; Riveting, Assembling doublers and brackets.	03/05/2018	2	Halanda	Benedikovic
FUSELAGE KIT	39 CONTROL SYSTEM	39-6 Fabricated spacer, drilled, primed & riveted the Elevator Idler Arm.	03/05/2018	1	Halanda	Benedikovic
FUSELAGE KIT	27 FIREWALL	Removing the bracket with rivets out of spec WD-1002-L-PC	03/05/2018	1.25	Halanda	Benedikovic
FUSELAGE KIT	30 STEP INSTALLATION	30-2 -> 30-4 Installing steps with additional stiffening plates riveted from the backside of where the delrin is mounted. Additionaly step bushings from TCW Tech were added.	04/05/2018	3.25	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	29-5 ; 29-8 ; 29-17 (deburring, dimpling, bending, priming)	12/05/2018	2.5	Halanda	Benedikovic
FUSELAGE KIT	35 ACCESS COVERS AND FLOOR PANELS	35-2 (Floor panels installation)	12/05/2018	1.5	Halanda	Benedikovic
INVENTORY	Spare & Replacement Parts	Spare & Replacement parts	14/05/2018	0.25	Halanda		Spare & Replacement Parts from Vans
FUSELAGE KIT	29 FUSE SIDE SKINS / 30 Step Installation	Glecoed Side Skins & Steps Priming	14/05/2018	3.5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	Access / Inspection Covers, 33 Baggage Area	(33-2) Baggage Floors w. Inspection Covers	16/05/2018	5.5	Halanda	Benedikovic
INVENTORY	Spare & Replacement Parts	Received the replacement bracket from Vans with spare parts as well as rivets and brake hoses.	29/06/2018	0.3	Halanda
ENHANCEMENTS	Access / Inspection Covers	Cutting an opening for the tunnel access/inspection cover.	30/06/2018	1.5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	27 FIREWALL, BERINGER Brakes, 38 URDDER PEDALS & BRAKE SYSTEM	Installing the Rudder Pedal Bearing Block together with the Beringer Parking Brake Valve on the Pilot’s side & replacing the WD-1002-L-PC bracket which was removed before due to rivets out of spec	03/07/2018	5.75	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	Riveting the Side Skins.	04/07/2018	3.5	Halanda, Benedikovic Jr.	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	(29-18) Glecoing the FWD Side Skins.	05/07/2018	0.5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	29 FUSE SIDE SKINS, ACCESS / INSPECTION COVERS	(33-2) Preparing the seat floors according to plans + creating access/inspection openings.	07/07/2018	5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	29 FUSE SIDE SKINS, ACCESS / INSPECTION COVERS	(33-2) Seat Floors - Openings were drilled for goose necks which will be covered by the side panels. Parts primed and nutplates riveted.	09/07/2018	8.5	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	(29-18) FWD Side Skins- Karol B. Jr. riveting the FWD Side Skins today..	14/07/2018	3.75	Benedikovic Jr.	Benedikovic
FUSELAGE KIT	31 UPPER FWD FUSELAGE ASSEMBLY	(31-1 -> 31-10) Starting works on Section 31 (following plans, basic preparation)	15/07/2018	5	Halanda	Benedikovic
FUSELAGE KIT	31 UPPER FWD FUSELAGE ASSEMBLY	(31) Dimpling, Deburring & Priming Parts	16/07/2018	3	Halanda	Benedikovic
FUSELAGE KIT	31 UPPER FWD FUSELAGE ASSEMBLY	(31) ..works continue on Upper FWD Fuse Assy, Upper skin dimpled & glecoed	17/07/2018	4	Halanda	Benedikovic
FUSELAGE KIT	31 UPPER FWD FUSELAGE ASSEMBLY	(31) Upper FWD Fuse Assy - preparations finished, ready for final riveting.	18/07/2018	2.5	Halanda	Benedikovic
FUSELAGE KIT	32 TAILCONE ATTACHEMENT	32-1 -> 32-6 Tailcone Attachement - following plans	19/07/2018	7.5	Halanda	Benedikovic
FUSELAGE KIT	30 STEP INSTALLATION	(30) Following plans	20/07/2018	4	Halanda	Benedikovic
FUSELAGE KIT	32 TAILCONE ATTACHEMENT	Riveting the tailcone with fuse together as called out in the plans.	22/07/2018	4.8	Halanda	Benedikovic
FUSELAGE KIT	40 FLAP SYSTEM	(40-4 -> 40-8) As called out in the plans.	23/07/2018	6	Halanda	Benedikovic
INVENTORY	ANDAIR Fuel System	Inventory and inspection of ANDAIR components. Consisting of: Fuel Pump, Fuel Valve Selector with ext. rod, 2 Gascolators (one for each wing)	24/07/2018	1	Halanda
FUSELAGE KIT	32 TAILCONE ATTACHEMENT	(32) Last rivets set to attach both main parts..	27/07/2018	2.5	Halanda	Benedikovic
FUSELAGE KIT	28 FWD FUSE RIBS BHDS BOTTOM SKINS	(28) Riveting panels in place.	27/07/2018	3.5	Halanda	Benedikovic
FUSELAGE KIT	29 FUSE SIDE SKINS	(29-21) Installing the Landing Gear Mount.	28/07/2018	4.75	Halanda	Benedikovic
ENHANCEMENTS	ELECTRICAL CONDUITS	Installation of Electrical Conduits in fuselage.	30/07/2018	3.75	Halanda	Benedikovic
FUSELAGE KIT	33 BAGGAGE AREA	(33-1 -> 33-6) Riveting as called out in plans.	07/08/2018	9	Halanda	Benedikovic
FUSELAGE KIT	34 BAGGAGE DOOR	Manufacturing the Baggage Door	10/08/2018	7.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Initial 3D Instrument Panel Planing	15/08/2018	9.5	Halanda		planing
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D Design work continues	17/08/2018	6	Halanda		planing
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D Designing push buttons & descriptions	19/08/2018	3.5	Halanda
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D Design: Push buttons, Warning Lights & Toggle switches placed on the instrument panel. Looking for the best place with ergonomy.	20/08/2018	4	Halanda
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D Design: Backup EFIS & Master Switch added.	30/08/2018	3	Halanda
ELECTRICAL & AVIONICS	ELECTRICAL & AVIONICS	3D Design: Rendering the panel with 'live' displays and backlit some of the switches for visualization.	03/09/2018	4.5	Halanda
FUSELAGE KIT	42 REAR SEAT BACKS	(42) Manufacturing Rear Seat Backs	05/09/2018	5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	37 FUEL SYSTEM, ANDAIR FUEL SYSTEM	Manufacturing the fuel lines to the gascolators and finding a suitable place to mount them. Both gascolators will be hidden in the wing roots.	06/09/2018	2	Halanda	Benedikovic
FUSELAGE KIT	42 REAR SEAT BACKS	(42) Rear Seat Backs primed & mounted	06/09/2018	3	Halanda	Benedikovic
FUSELAGE KIT	37 FUEL SYSTEM, 38 RUDDER PEDALS & BRAKE SYSTEM	(38 & 37)Brake & Fuel Lines installation	07/09/2018	7.75	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D Design: I have redesigned the pushbutton for disconnecting all autopilot servos/trim & flap motors with one button..	09/09/2018	1.5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	37 FUEL SYSTEM, ANDAIR FUEL SYSTEM	Fabricating, priming & installing mount brackets for both ANDAIR gascolators.	09/09/2018	3.5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	37 FUEL SYSTEM, ANDAIR FUEL SYSTEM	The bracket looks a bit complicated; the goal was to have the fuel pump easily accessible from the Inspection Access Hatch. Fabricated the fuel line from the ANDAIR fuel selector to the ANDAIR fuel pump. This fuel pump features an internal bypass.	11/09/2018	6.75	Halanda	Benedikovic
FUSELAGE KIT	39 CONTROL SYSTEM	Installing the rudder cables with fairings.	12/09/2018	3.25	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Rendering with the new switch. I am not happy with the current location and will most likely move it to the left side of the panel.	13/9/2018	1.5	Halanda	Benedikovic
FUSELAGE KIT	39 CONTROL SYSTEM	Installation as plans call out. Rudder pedals powder coated black.	13/09/2018	7.75	Halanda	Benedikovic
FUSELAGE KIT	39 CONTROL SYSTEM, 40 FLAP SYSTEM	Respective chapters -following plans.	14/09/2018	9	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	BERINGER BRAKES, 38 RUDDER PEDALS & BRAKE SYSTEM	Rudder Pedals with Beringer Master Cylinders installation.	15/09/2018	4.5	Halanda	Benedikovic
FUSELAGE KIT, ENHANCEMENTS	BERINGER BRAKES, 38 RUDDER PEDALS & BRAKE SYSTEM	Installation of BERINGER Hydraulic brake houses. Following BERINGER installation manual.	18/09/2018	6.75	Halanda	Benedikovic
FUSELAGE KIT	44 WING ATTACHEMENT	Priming the skin and installing the root fairing supports on the fuselage skin.	19/09/2018	5.75	Halanda	Benedikovic
FUSELAGE KIT	39 CONTROL SYSTEM	(39) Finishing Rudder Cables installation.	21/09/2018	2.5	Halanda	Benedikovic
ENHANCEMENTS	RUDDER TRIM	Manufacturing a Rudder Trim prototype. The trim will actuate directly on the rudder pedals with the help of an electrical servo motor. Finding the proper spring length with proper tension will be a challenge.	23/09/2018	4.5	Halanda	Benedikovic	Prototype
ENHANCEMENTS	RUDDER TRIM	Servo motor installed and connected to the copilot’s left rudder pedal.	25/09/2018	4	Halanda	Benedikovic	Prototype (Won't be connected during initial test flights)
INVENTORY	ANDAIR FUEL SYSTEM COMPONENTS	ANDAIR elbows, blanking plugs and drain valves for both fuel gascolators.	02/10/2018	0.25	Halanda
ENHANCEMENTS	ACCESS / INSPECTION COVERS	Manufacturing and riveting the backplate with nutplates to the tunnel acccess/inspection cutout.	02/10/2018	2.5	Halanda	Benedikovic
INVENTORY	Fans, Grills & Lemo Plugs	Defrost Fans with Grills & DC Lemo Plug Install Kit	03/10/2018	0.25	Halanda
ENHANCEMENTS	OP-41	ELT bracket drilled, primed and riveted nutplates, finally riveted in the e-bay/battery compartment.	03/10/2018	2.5	Halanda	Benedikovic
FUSELAGE KIT	44 WING ATTACHEMENT	(44) Manufacturing and priming Wing Root Fairings as called out in plans.	03/10/2018	3.5	Halanda	Benedikovic
ENHANCEMENTS	ANDAIR FUEL SYSTEM	Installing ANDAIR plugs, elbows & drain valves on each gascolator.	04/10/2018	0.75	Halanda	Benedikovic
ENHANCEMENTS	OVERHEAD CONSOLE / SYSTEM	NACA Cutouts for Overhead Fresh Air	04/10/2018	2	Halanda	Benedikovic
FINISH KIT	50 CABIN HEAT & VENTILATION	(50) PIC & COPI Front NACA Vents installed.	08/10/2018	3.5	Halanda	Benedikovic
ENHANCEMENTS	ACCESS / INSPECTION COVERS	Rear Bulkhead Access Door Cutout: Cutout was done using a water jet. The access will be hinged on the upper part to allow quick and easy access to the battery / electronic-bay.	09/10/2018	8	Halanda	Benedikovic
ENHANCEMENTS	ACCESS / INSPECTION COVERS	Rear Bulkhead Access Door: Completed with 2 locking latches and primed on the battery/e-bay side.	10/10/2018	7.5	Halanda	Benedikovic
INVENTORY	New Parts Arrival	Inventory of items: Door Strut Attach Brackets (Planearound), New Door 180 Kit (Planearound), Wheel Bracket Fairing Spacers (Planearound), Angled Door Pins & Delrin Pin Guides (Planearound), Sirs Light Aircraft Compass, Rudder Pedal Extensions from (JD Air), Infinity Grips, Carling backlit (Mom ON-OFF-ON Mom) Switches and Blends.	11/10/2018	1	Halanda
FUSELAGE KIT	31 UPPER FWD FUSELAGE ASSEMBLY	(31-2 -> 31-9) Riveting the Subassembly to Fuselage, FWD Fuse Top Skin dimpled & Rear Bulkhead primed from the cabin side.	11/10/2018	2	Halanda	Benedikovic
FUSELAGE KIT	33 BAGGAGE AREA	(33-10) Installing the Wear Blocks to the Baggage Bulkhead.	11/10/2018	1.5	Halanda	Benedikovic
FUSELAGE KIT	43 CABIN COVER	(43) Started works on the repaired Cabin Cover & first test fit.	15/10/2018	9.5	Halanda	Benedikovic
FUSELAGE KIT	43 CABIN COVER	(43-1 -> 43-13) Triming & Match Drilling Cabin Top.	16/10/2018	8.75	Halanda	Benedikovic
INVENTORY	Various new parts arrival	ROSEN Sun Visors, SUPERIOR PANEL TECHNOLOGY Light Strip, External Power Receptacle, External Power Plug, Electrical Cables, Pitot / Static Tube System, Antennas (Marker Beacon, DME, TXPD, ADS-B, FLARM, 2xVHF), Ray Allen POS-12 Position Sensor, Hidden Oil Door Hinge & various fittings, grommets, New primer spray cans from Colorlak	16/10/2018	1	Halanda
ENHANCEMENTS, ELECTRICAL & AVIONICS, PITOT STATIC SYSTEM	PEDAL EXTENSIONS, WING ELECTRICS, PITOT STATIC SYSTEM	Installing Corrugated Conduits in Wings, grommets in the fuselage to protect conduits, JD Pedal Extensions, Pitot & AOA tubes in L Wing.	18/10/2018	6	Halanda	Benedikovic
PITOT STATIC SYSTEM	PITOT STATIC SYSTEM	Static System Installation in tailcone.	21/10/2018	4	Halanda	Benedikovic
ELECTRICAL & AVIONICS, PITOT STATIC SYSTEM	External Power Connector, PITOT STATIC SYSTEM	Works continued on the Pitot Static system (Wings – Fuselage Attach Points). 3D printing conduit holders for the Electronic / Battery Bay Compartment & Ext Power Plug Cover. Manufacturing the Baseplate for the Ext Power Connector incl a switch (for either charging the battery with a regulated Ext Pwr or unregulated for engine start only).	22/10/2018	6	Halanda	Benedikovic
ELECTRICAL & AVIONICS	External Power Connector	External Power Connector Base Plate: Finished, primed & installed.	23/10/2018	4	Halanda	Benedikovic
FUSELAGE, ENHANCEMENTS	40 FLAP SYSTEM, FLAP POSITION SENSOR	Manufacturing, priming and installation of an L-Bracket for the Flaps Position sensing.	23/10/2018	3	Halanda	Benedikovic
WINGS	20 BOTTOM WING SKINS	(20-5 -> 20-6) Riveting Inboard Bottom Skins on both wings.	25/10/2018	5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Cutting holes for 2 Defrost/Avionics Cooling Fans. The SilverStone 80mm grills will be mounted from below.	26/10/2018	1.5	Halanda	Benedikovic
WINGS	20 BOTTOM WING SKINS	(20-5 -> 20-6) Riveting Outer Bottom R-Wing Skin.	31/10/2018	3.5	Halanda	Benedikovic
WINGS	24 WING TIP	(24) Wing Tip R-Wing. Installing the wing tip on R-wing using hinges (Mouser method).	05/11/2018	6.75	Halanda	Benedikovic
INVENTORY	Various parts received	GARMIN Pitot with regulator, GARMIN AutoPilot Servos with Connector Kits, Limit switches mechanical & reed sensor, ANDAIR Oil / Air Separator	07/11/2018	0.75	Halanda
WINGS	24 WING TIP	(24) Wing Tip R-Wing; ..works continue, riveted & bonded with Araldit. Manufactured carbon fiber rib (to copy aileron trailing edge) installed.	07/11/2018	6	Halanda	Benedikovic
ENHANCEMENTS	EXTERIOR LIGHTS		11/11/2018	3	Halanda	Benedikovic
WINGS, ENHANCEMENTS, ELECTRICAL & AVIONICS	ANTENNAS, 24 WING TIP, EXTERIOR LIGHTS	Landing Light Bracket Primed & Installed with light, (24) filling the gap between wing & wing tip, ADS-B IN Antenna installation.	13/11/2018	6.75	Halanda	Benedikovic
ELECTRICAL & AVIONICS, ENHANCEMENTS	WINGS, OP38 ELECTRIC AILERON TRIM	GARMIN Auto Pilot Roll Servo & Roll Trim Servo springs installed. Following Vans & Garmin install manual.	15/11/2018	3.75	Halanda	Benedikovic
ELECTRICAL & AVIONICS, ENHANCEMENTS	FUSELAGE	GARMIN Auto Pilot Pitch Servo installed - following Garmin install manual.	17/11/2018	2.75	Halanda	Benedikovic
PITOT STATIC SYSTEM	PITOT STATIC SYSTEM	Installing Heated & Regulated GARMIN Pitot Tube + looking for a good place for installing the regulator.	19/11/2018	1.5	Halanda	Benedikovic
INVENTORY	Connectors & Push/Pull Cables received.	INVENTORY TE DT&DTM Deutsch Connectors & Push/Pull Cables.	22/11/2018	2	Halanda
WINGS, PITOT STATIC SYSTEM	20 BOTTOM WING SKINS	(20-5 -> 20-6) Riveting Outer Bottom L-Wing Skin. Installation of Pitot Tube with Gretz Mast finished.	22/11/2018	4.5	Halanda	Benedikovic
WINGS	24 WING TIP	(24) Wing Tip L-Wing. Same process and method like done and documented on R-Wing..	24/11/2018	6	Halanda	Benedikovic
WINGS	24 WING TIP	(24) Wing Tip L-Wing ..works continue. Leaving the Araldit bond to cure close to the source of heat.	26/11/2018	4.5	Halanda	Benedikovic
INVENTORY	BERINGER BRAKES received	BERINGER FUSELAGE KIT: Wheels, Brakes (with floating calipers), tubes, brake bleeding kit & components incl. tire changing tools for different tire sizes received.	27/11/2018	1	Halanda
WINGS	24 WING TIP	(24) Wing Tip L-Wing - Finishing the works on the Left Wing Tip. Carbon fiber rib installed & gap filled with EPOXY and micro between wing skin and tip.	30/11/2018	2.75	Halanda	Benedikovic
INVENTORY	Switches	Flap Switch & Alternate Static Air Source switch - Honeywell MicroSwitch (Mom ON-OFF-Mom ON). The Alt Static Air Source switch will open a hole in the switch body to allow for alternate static cabin air source in case both outer static sources get plugged.	03/12/2018	0.25	Halanda
							11/12/2018 Inspected by The Transport Authority of Slovak Republic
PITOT STATIC SYSTEM, ELECTRICAL & AVIONICS		Garmin Pitot Heat Regulator mounted	11/12/2018	2.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Flap Switch Actuator 3D design for the Instrument Panel visualization.	18/12/2018	1	Halanda
ELECTRICAL & AVIONICS	ANTENNAS	Mounting the VHF, TXPD & Marker Beacon Antennas on the belly.	18/12/2018	6	Halanda	Benedikovic
INVENTORY		-Door gas struts (Bansbach B0N0F50-100-247/530N Gas Spring 4″(100mm) Stroke 10″(247mm) A1 M8 Hinge Eye -have to order E2 M8 to fit the Plane Around attach brackets. -Push & Pull controls for heating, parking brake and Engine Alternate Air -firewall passthrough	18/12/2018	0.25	Halanda
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Instrument Panel 3D visualization with Flaps Actuator&Switch	19/12/2018	2.5	Halanda
EMPENAGE KIT	12 EMPENAGE FAIRINGS	(12-5 -> 12-6) Starting adjustments and installation of the tailcone fairing.	19/12/2018	3	Halanda	Benedikovic
EMPENAGE KIT	12 EMPENAGE FAIRINGS	(12-5 -> 12-6) Works on tailcone fairing	21/12/2018	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Instrument Panel 3D rendering; Backup battery guard removed. Static source guarded switch moved to the left panel + minor changes.	22/12/2018	5.5	Halanda
ENHANCEMENTS	EXTERNAL POWER CONNECTOR	Replacing the external power switch with a guarded version for selecting the main battery contactor on or off with external power connected.	4/1/2019	0.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS, EMPENAGE KIT	EXTERNAL POWER CONNECTOR, ANTENNAS, 12 EMPENAGE FAIRINGS	..works continue on the tailcone fairing + support bracket installed for the external power recept. Finding the right mounting place for the upper VHF antenna.	4/1/2019	6.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Design works on the Instrument Panel: Modeling an Air Vent TRAFFIC MUTE switch added COMPSS LIGHT switch added IND LTS switch repositioned to the R Panel Placing the equipment on the rear instrument wall (sub-panel)	6/1/2019	8.5	Halanda
EMPENAGE KIT	12 EMPENAGE FAIRINGS	Tailcone Fairing finished	8/1/2019	7	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D design work: Added Deuce Schottky Diode Heat Sink & FLARM AT-1 warning system Added Vishay potentiometers for switch backlighting and glareshield	10/1/2019	6	Halanda	Benedikovic
ELECTRICAL & AVIONICS	ANTENNAS	VHF Antenna Mount on Tailcone	12/1/2019	6.5	Halanda	Benedikovic
INVENTORY		DEUCE SCHOTTKY DIODE for Essential Bus & Grinder	15/1/2019	0.25	Halanda
ENHANCEMENTS	BERINGER Brakes & Parking Brake	Manufacturing and installing a bracket to hold the parking brake sensor & cable.	16/1/2019	4	Halanda	Benedikovic
ENHANCEMENTS	Misc	Manufacturing the center console for rear seats.	17/1/2019	3	Halanda	Benedikovic
INVENTORY		Received VISHAY Potentiometers 10kOhm (MIL spec)	17/1/2019	0.25	Halanda
ENHANCEMENTS	Misc	Rear Seats Center Console update	21/1/2019	4.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D Design Work: Minor Design Update on the Instrument Panel	22/1/2019	3.5	Halanda
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Getting Mesh Data of the Aerosport 310 Panel	3/2/2019				Aerosport 3D panel Mesh Data recieved
ENHANCEMENTS	OVERHEAD CONSOLE / SYSTEM	Overhead Console Vents & Alu Flanges	5/2/2019	6.5	Halanda	Benedikovic
WINGS KIT	24 WING TIP	(24-2) Cee Baylees Wing Tip Lenses	9/2/2019	3.5	Halanda	Benedikovic	UPDATE: Unfortunately CEE BAYLEES never responded to my complaints. I'll have to order the original ones from Vans..
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Andair Fuel Valve added to Cockpit Visualization	12/2/2019	1.5	Halanda
ENHANCEMENTS	CENTER CONSOLE	Throttle Quadrant Connecting Points	22/2/2019	5.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Fitting the Aerosport 310 panel	7/3/2019	7.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Fitting the Aerosport 310 panel incl. vents	8/3/2019	3	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Fitting the Aerosport 310 panel w. Armrest	11/3/2019	6	Halanda	Benedikovic
FUSELAGE KIT / ENHANCEMENTS	37 FUEL SYSTEM / ANDAIR FUEL SYSTEM	(37) Fitting the ANDAIR Fuel Selector to the Aerosport Armrestpanel	12/3/2019	7.5	Halanda	Benedikovic
INVENTORY / INSTRUMENT PANEL		Inventory: APEM Master & Backup Switches received	12/3/2019	.25	Halanda
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Mounting the Aerosport Throttle Quadrant: ..mating the throttle quadrant to the tunnel & the aerosport center console. Made holes for the push&pull cables to operate the parking brake and the alternate engine air in the left side panel and forward & rear heat in the right panel.	14/3/2019	5.5	Halanda	Benedikovic
INVENTORY		Inventory: ANDAIR Fitting Extensions & Sphere Steel Grommets: Received the Andair Fitting Extensions for the Gascolators to route the tubes downwards + Sphere Steel Grommets for the firewall to accomodate the push/pull cables.	15/3/2019	0.25	Halanda
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Received planes created out of mesh data: ..for the cockpit visualization.	15/3/2019
ENHANCEMENTS	ANDAIR FUEL SYSTEM	Mounting Andair Fitting Extensions: ..on both sides L & R	16/3/2019	1	Halanda	Benedikovic
ENHANCEMENTS	INSTRUMENT PANEL	Starting works on the cockpit visualization incl. the 310 panel	17/3/2019	8.5	Halanda
ENHANCEMENTS / FUSELAGE KIT	Misc / 27 FIRE WALL	Mounting the Sphere Steel Grommets to the Firewall: ..and checking operation with the push and pull cables. The lowest thing push&pull is there to operate the Alternate Engine Air.	18/3/2019	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS / ENHANCEMENTS	INSTRUMENT PANEL / CENTER CONSOLE	Drilling holes for electrical switches	19/3/2019	1.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Details on the Cockpit Visualization: Background and text for flaps UP and DN adjusted.	20/3/2019	0.5	Halanda
FINISH KIT	47 SPINNER & COWLING	(47) Cowl Attach Hinges: (47-6 -> 47-8) Fabricating and riveting the Cowl Attach Hinges.	20/3/2019	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Laser test engraving rocker switches	27/3/2019				Samples received from our partner company: TECHMIND
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Spray painting push buttons & indicators: ..with Black Matte RAL 9005	4/4/2019	1	Halanda
INVENTORY		Inventory: Gas strut attachements, GPS Antennas, Firewall Foil	18/4/2019	0.25	Halanda
INVENTORY		Inventory: Arrival of the Finnish Kit	23/4/2019	9	Halanda
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Update on the 3D Cockpit Visualization	24/4/2019	4.5	Halanda
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Cabin Doors: (45-02 -> 45-03)	25/4/2019	5	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Cabin Doors: (45-02 -> 45-05)	26/4/2019	6.5	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM	(45) Cabin Doors & PlaneAround Door Locking Mechanism: (45-02 -> 45-05) + PlaneAround Door Locking System	27/4/2019	6.5	Halanda	Benedikovic
ENHANCEMENTS	BERINGER BRAKES & PARKING BRAKE	Parking Brake Sensor Final Installation	28/4/2019	3.5	Halanda	Benedikovic
FINISH KIT	46 ENGINE MOUNT & LANDING GEAR	(46) Initial line up and mounting of the Engine Mount: (46-2) …with some initial difficulties to line up the holes	29/4/2019	2.25	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Cabin Doors: Glueing together both halves.	29/4/2019	3.5	Halanda	Benedikovic
INVENTORY		Inventory: Wheelen Dome Lights: The first is planed to light up the cabin, the second to light up the baggage compartment.	30/4/2019	0.25	Halanda	Benedikovic
ENHANCEMENTS	MISC	Sealing the Firewall with RTV	30/4/2019	0.5	Halanda	Benedikovic
ENHANCEMENTS	OP48 AHRS BRACKET	(OP-48) AHRS BRACKET mount: The bracket will be utilized to hold the DME & TXPD external modules and some more items.	1/5/2019	2.75	Halanda	Benedikovic
FUSELAGE KIT	31 UPPER FWD FUSELAGE ASSEMBLY	(31) FWD Fuse Top riveted to Fuselage: (31-9) Had to use a spacer on the left half to avoid folded skin.	2/5/2019	2.25	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Flap Handle repainted	2/5/2019	0.75	Halanda	Benedikovic
INVENTORY		Inventory: Engine Heating Pads 220V, various screws, BOELUBE Paste, Ignition Switch with keylocks	3/5/2019	0.5	Halanda
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Cabin Doors: (45-02 -> 45-05)	4/5/2019	3.5	Halanda	Benedikovic
ENHANCEMENTS	OVERHEAD CONSOLE / SYSTEM	NACA Air Inlets for Overhead Tunnel	4/5/2019	3	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Keyed Ignition Switch 3D model added to Panel Visualization	4/5/2019	1.5	Halanda	Benedikovic
ENHANCEMENTS	MISC	Firewall Heat & Soundproofing Foil applied	5/5/2019	1.5	Halanda	Benedikovic
FINISH KIT	50 CABIN HEAT AND VENTILATION	(50-2) Heater Ducts installed	6/5/2019	1	Halanda	Benedikovic
FINISH KIT	46 ENGINE MOUNT & LANDING GEAR	Engine Mount	6/5/2019	0.75	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	Cabin Doors: Working on cabin doors..	7/5/2019	5.5	Halanda	Benedikovic
INVENTORY		INVENTORY: Except for glecos and some chemicals, I received the door rubber seals.. Trimlok 100 series: 3100B3X1/4A	13/5/2019	0.5	Halanda
ENHANCEMENTS / FUSELAGE KIT	OVERHEAD CONSOLE/SYSTEM / 43 CABIN COVER	OVERHEAD CONSOLE: Preparation for gluing in the Overhead Console	15/5/2019	7.5	Halanda	Benedikovic
ENHANCEMENTS	OVERHEAD CONSOLE/SYSTEM	OVERHEAD CONSOLE: glued in..: Overhead Console glued in including left and right conduit.	16/5/2019	4.5	Halanda	Benedikovic
ENHANCEMENTS	OVERHEAD CONSOLE/SYSTEM	Sun Shields & Conduits to Overh. Console	17/5/2019	5.5	Halanda	Benedikovic
ENHANCEMENTS	OVERHEAD CONSOLE/SYSTEM	Conduits / Overhead Console	20/5/2019	5.25	Halanda	Benedikovic
ELECTRICAL & AVIONICS	ANTENNAS	Top Mounted Antennas: ..installed	21/5/2019	3	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Cabin Doors	22/5/2019	6.5	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Cabin Doors: Right door and cabin will need better alignment..	28/5/2019	7.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Interior Color & Leather pick: Looking for the right interior colors to match the interior handles and Aerosport panels + leather choice.	17/6/2019	2.25	Halanda
ENHANCEMENTS / FUSELAGE KIT	OVERHEAD CONSOLE / SYSTEM / 43 CABIN COVER	(43) Match Drilling Cabin Cover: Match drilling the cabin cover with the Overhead Console	8/7/2019	1.25	Halanda	Benedikovic
ENHANCEMENTS	MISC	Door Seals: Fitting and trimming the door seals.	11/7/2019	6.75	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM	(45) Door Handles & Mechanism: 45-10 -> 45-14	12/7/2019	7.5	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM	(45) Door Handles & Mechanism: 45-10 -> 45-14	13/7/2019	6.25	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM	(45) Door Handles & Mechanism: 45-10 -> 45-14	17/7/2019	4.5	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	45 CABIN DOORS & TRANSPARENCIES / PLANEAROUND DOOR LOCKING SYSTEM	(45) Door Handles & Mechanism: 45-10 -> 45-17	19/7/2019	3.25	Halanda	Benedikovic
ENHANCEMENTS	MISC. / OVERHEAD CONSOLE / SYSTEM	Baggage Light Installation: Model: Whelen 7081307	22/7/2019	0.75	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS / FUSELAGE KIT	MISC. / CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43)(45) Doors and Door Seals: Making a bed of epoxy for the the door seals and epoxying the delrin guides in place on the doors.	23/7/2019	7.5	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS / FUSELAGE KIT	MISC. / CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43)(45) Doors and Door Seals: Right epoxy bed is finished, now on to the left side..	26/7/2019	6.25	Halanda	Benedikovic
ENHANCEMENTS	OVERHEAD CONSOLE/SYSTEM / ELECTRICAL CONDUITS	Cabin Top Conduits: Fine tuning the cabin top’s corrugated conduit covers.	30/7/2019	4.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Cabin Top furnishing: Preparing/trimming the laminated interior parts for furnishing the cabin top.	1/8/2019	1.75	Halanda	Benedikovic
ENHANCEMENTS / FUSELAGE KIT	OVERHEAD CONSOLE/SYSTEM / 43 CABIN COVER	(43) Cabin Cover & Overhead Console System: Filling and sanding the cabin top inside + fabricating a laminated cover for the Center Cabin Brace.	3/8/2019	5.75	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Gas Strut Installation: 45-16 + door attaching brackets modified	12/8/2019	3.5	Halanda	Benedikovic
FUSELAGE KIT / PAINT/FURNISHING/UPHOLSTERY	33 BAGGAGE AREA / 43 CABIN COVER	Spray painting with interior color: Spray painting the Cabin Cover/Top and other parts with interior color.	14/8/2019	1.5	Halanda	Benedikovic
FUSELAGE KIT	43 CABIN COVER	(43) Cabin Cover mating with Fuselage: 43-4 -> 43-7 Final Fitting the Cabin Cover on the Fuselage + Windshield alignement	15/8/2019	8.25	Halanda	Benedikovic
FUSELAGE KIT	43 CABIN COVER	(43) Cabin Cover mating with Fuselage: 43-4 -> 43-7	16/8/2019	6.5	Halanda	Benedikovic
FINISH KIT / PAINT/FURNISHING/UPHOLSTERY	45 CABIN DOORS & TRANSPARENCIES	(45) Preparing for Windshield installation: 45-18 -> 45-19 & creating template for the shield leather cover.	19/8/2019	1.5	Halanda	Benedikovic
PAINT/FURNISHING/UPHOLSTERY		Glareshield paint: 1 layer of epoxy primer + RAL 9017 Matte Black	20/8/2019	0.25	Halanda	Benedikovic
FINISH KIT / FUSELAGE KIT	45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43) (45) Cabin Cover & Doors + Door sills: The door sills are carbon fiber and come from Aerosport. Building covers for the door hinges..	21/8/2019	3.75	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Door hinge covers	22/8/2019	2.5	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	45 CABIN DOORS & TRANSPARENCIES / ANDAIR OIL SEPARATOR	(45) Door hinge covers & Oil Separator Mount: Andair Oil Separator Mount on the firewall next to the Brake Fluid Reservoir.	24/8/2019	3.75	Halanda	Benedikovic
FUSELAGE KIT	43 CABIN COVER	(43) Center Cabin Brace: Mounting the Center Cabin Brace in position..	27/8/2019	1.25	Halanda	Benedikovic
ENHANCEMENTS	ANDAIR OIL SEPARATOR	Andair Oil Separator Mount: One more additional support bracket on the upper back side of the separator.	28/8/2019	1.75	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Door gaps & rear windows: Adjusting the door gaps and attaching the rear pax windows with Lord Adhesive (7545A/E).	2/9/2019	4.75	Halanda	Benedikovic
INVENTORY		INVENTORY: USB Charging Ports: by CommitLift: http://commitlift.com/USBASinstructions.pdf	2/9/2019	0.25	Halanda
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Door Gaps: ..working on door gaps	3/9/2019	4.25	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Door Gaps	5/9/2019	6.5	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Windows: 45-18 -> 45-19 Glueing in pax windows and windshield. Checking clearance/depth of the Overhead Panel.	9/9/2019	7.5	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Windshield: 45-18 -> 45-19	10/9/2019	5.5	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Windshield: 45-18 -> 45-19	12/9/2019	2.75	Halanda	Benedikovic
FINISH KIT / INVENTORY	45 CABIN DOORS & TRANSPARENCIES	(45) Windshield + INVENTORY: 45-18 -> 45-19 Received the 12V power plug -it’s intended for the baggage compartment.	13/9/2019	3	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Windshield: 45-18 -> 45-19	14/9/2019	2.75	Halanda	Benedikovic
FINISH KIT / FUSELAGE KIT	45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43)(45) Cabin Top tuning & Windshield: Tuning the cabin top’s B pillars to match the door’s curvature and works on the windshield according to plans..	15/9/2019	6.25	Halanda	Benedikovic
PAINT/FURNISHING/UPHOLSTERY		Upholstery professional visit: Today Peter Skrabalek -an upholstery professional and glider pilot visited our Skunk works to check what can be done with the seats and other interior details..	16/9/2019
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Windows: Glueing in a door window, working on the windshield and fine tuning/sanding the gaps on the pax windows.	19/9/2019	4.5	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Door Windows & Windshield	20/9/2019	5.5	Halanda	Benedikovic
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) Windows: All windows glued in place..	21/9/2019	1.25	Halanda	Benedikovic
FUSELAGE KIT	43 CABIN COVER	(43) Filling transitions between fuselage and Cabin Cover	22/9/2019	8.5	Halanda	Benedikovic
PAINT/FURNISHING/UPHOLSTERY		First carpets are finished: These belong to the baggage compartment, the actual color is black. Thanks to Stefan Michalicka who did a fantastic job.	23/9/2019
FINISH KIT	45 CABIN DOORS & TRANSPARENCIES	(45) More fiberglass around windows: Laying some more fiber around the windows to smooth the transitions..	23/9/2019	4.5	Halanda	Benedikovic
PAINT/FURNISHING/UPHOLSTERY		Trimming carpets: Fine tuning the carpet edges to get a proper fit on the floor. Stefan at work..	24/9/2019	3.5	Halanda	Benedikovic
FINISH KIT / FUSELAGE KIT	45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43)(45) Trimming gaps and transitions: ..never ending story! We wish Vans would deliver a much better fiberglass components. You literally spend weeks with filling, sanding, trimming..	24/9/2019	4.5	Halanda	Benedikovic
FINISH KIT / FUSELAGE KIT	45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43)(45) Trimming gaps and transitions: ..same story today	25/9/2019	7	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	46 ENGINE MOUNT & LANDING GEAR / BERINGER BRAKES & PARKING BRAKE	(46) Landing Gear BERINGER: A deviation from Vans plans using the BERINGER wheels and brakes RV-10 kit. Getting ready for installation.	28/9/2019	3.5	Halanda	Benedikovic
INVENTORY		INVENTORY Baggage Net and engine mount covers: Today I received the baggage net, both engine mount carbon covers and a handle cover replacement (got damaged during installation). The last 2 items came from AeroSport – super friendly customer service!	30/9/2019	0.25	Halanda
FINISH KIT / FUSELAGE KIT	45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43) (45) More filling and sanding..	2/10/2019	8.75	Halanda	Benedikovic
FINISH KIT / FUSELAGE KIT	45 CABIN DOORS & TRANSPARENCIES / 43 CABIN COVER	(43) (45) More filling and sanding..	3/10/2019	9	Halanda	Benedikovic
ENHANCEMENTS / INVENTORY	INSTRUMENT PANEL	Laser etched switches: Today I received my laser etched switches for the instrument panel from http://techmind.sk/en/ Mr. Martyscak, the owner of Techmind did a wonderful job. I’m very happy with the results..	4/10/2019
PAINT/FURNISHING/UPHOLSTERY / FUSELAGE KIT	43 CABIN COVER	Spray painting the Cabin Cover and Fuse: 2K Epoxy Primer	8/10/2019	5.5	Halanda	Benedikovic
ENHANCEMENTS / FUSELAGE KIT	BERINGER BRAKES & PARKING BRAKE / 43 CABIN COVER	(43) Cabin Cover finished: voilà	10/10/2019	7.75	Halanda	Benedikovic
ENHANCEMENTS / FINISH KIT	BERINGER BRAKES & PARKING BRAKE / 46 ENGINE MOUNT & LANDING GEAR	(46) Main & Nose Gear: Right landing gear incl. wheel was attached without issues but the pin on the left side wouldn’t go in and eventually bent. During removal the axle was damaged so I ordered a new one including 2 new pins from BERINGER. Forward leg mounted with rubber dampeners with no issues. We had to utilize a temporary support for the left side until we get replacement parts from BERINGER.	13/10/2019	7	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Starting works on the Wheel Fairings	15/10/2019	6.75	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Wheel Fairings	17/10/2019	7.75	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Gear Legs and Wheel Fairings	18/10/2019	6.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Gear Legs and Wheel Fairings	24/10/2019	8.75	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Switch & Pushbutton backlighting: Checking the switch backlighting with some 9V batteries. The pushbutton’s text will be visible when backlit only.	24/10/2019	0.5	Halanda
FINISH KIT / ENHANCEMENTS	48 GEAR LEG & WHEEL FAIRINGS / BERINGER BRAKES & PARKING BRAKE	(48) Left Main Gear attached: The spare parts from BERINGER arrived so we were able to mount the left leg with wheel and did some additional work on the fairings.	29/10/2019	4	Halanda	Benedikovic
FINISH KIT / ENHANCEMENTS	48 GEAR LEG & WHEEL FAIRINGS / BERINGER BRAKES & PARKING BRAKE	(48) Forward leg and wheel fairings	31/10/2019	7.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Finding the axes: For a proper wheel pants alignment we raised the main gears and drew axes on the floor..	2/11/2019	3	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Front leg and wheel fairings	3/11/2019	7.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Main Wheel Fairings: Aligning the main wheel fairings..	4/11/2019	6	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Main Wheel Fairings	5/11/2019	6.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Main Wheel Fairings: Slight deviation from plans: Fabricating a V-bracket to better support the fairing; saw this solution at some other builder’s website and liked it. The single bolt hole will be filled when finished.	6/11/2019	5.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Main Wheel V-brackets: Riveted and epoxied in place..	7/11/2019	3.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Wheel Fairings	8/11/2019	7.75	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Leg and Wheel Fairings	9/11/2019	6	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings: 48-10 -> 48-12	11/11/2019	5.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings	13/11/2019	3.5	Halanda	Benedikovic
PAINT/FURNISHING/UPHOLSTERY / FUSELAGE KIT		Carpets: Verifying the carpets fit and checking CG with some live weight in the baggage area 😀 I,ll have to cut out some openings for the heater outlets..	16/11/2019	0.75	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings: Works on the intersection fairings continue and we ran into a clearance issue with the upper intersection fairing and the ANDAIR gascollators on each side. We’ll have to sort that out later..	17/11/2019	1.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	3D design for the Instrument: I positioned a piezzo buzzer (free dowload from Grabcad) behind the instrument panel. This one will work as a backup and will be connected to the original Vans stall switch. The other design involves an external VR by B&C. It’s not a 100% accurate model but it’s good enough to check if you have enough space behind the panel.. Lastly I needed to move 2 screw holes on the left Aerosport instrument panel insert to accommodate the EFIS’s nutplates.	17/11/2019	6.25	Halanda	Benedikovic
ENHANCEMENTS	TOW BAR TAILCONE STORAGE	Tow Bar Mount in the tailcone: Mock-up of the Tow Bar Mount..	18/11/2019	4.75	Halanda	Benedikovic
ENHANCEMENTS	TOW BAR TAILCONE STORAGE	Tow Bar Mount: Fork holder finished -riveted, made of Carbon Fiber and reinforced with bracket.	19/11/2019	5.25	Halanda	Benedikovic
ENHANCEMENTS	TOW BAR TAILCONE STORAGE	Tow Bar Mount finished: Inspired by PILATUS PC6!	20/11/2019	2	Halanda	Benedikovic
INVENTORY		INVENTORY Milw. Scissors, Altn Door Spring, Rammount: The Alternate Air Door Spring is actually a C182 part nr. S2952-15	20/11/2019	0.25	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings	21/11/2019	3.5	Halanda	Benedikovic
ENHANCEMENTS	MISC.	12V plug & light push button: Installation of the 12V plug and baggage light push button.	22/11/2019	5	Halanda	Benedikovic
ENHANCEMENTS / ELECTRICAL & AVIONICS	ACCESS/INSPECTION COVERS / EXTERNAL POWER CONNECTOR	Baggage Bulkhead Door & Ext PWR Plug: Installing the baggage bulkhead door holder and the External Power Plug is now connected to the structure to avoid unintended loss in the tailcone or even worse: flight controls blockage.	25/11/2019	3.25	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings	28/11/2019	3.5	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings	30/11/2019	3	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings	5/12/2019	4	Halanda	Benedikovic
WELCOME		Situation Overview	11/12/2019	0.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Push Buttons & Indicators: Push Buttons & Indicators. Some of them will be readable only when backlit, that’s the idea. The push buttons can operate as discrete inputs for various systems (e.g. G3X touch to inhibit ESP-X or manually activate display Reversion).. There is a typo on the DSPL RERVERS button and I’ll have a new switch engraved. Push Buttons and indicators are high quality, made in Germany. Momentary or ON/OFF functions available.	13/12/2019	1	Halanda
FINISH KIT	47 SPINNER & COWLING	47-2 -> 47-3 Spinner Back Plate preparation, priming and assembly. 47-10 Works on Oil Door.	28/12/2019	3.5	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47 Various works on the cowl.	29/12/2019	2.25	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-10 Oil Door	30/12/2019	2.5	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-10 Oil Door	6/1/2020	2	Halanda	Benedikovic
FINISH KIT	48 GEAR LEG & WHEEL FAIRINGS	(48) Intersection Fairings	7/1/2020	3.75	Halanda	Benedikovic
INVENTORY		STRATUS USBs	14/1/2020	0.1	Halanda		STRATUS USBs
PAINT / FURNISHING / UPHOLSTERY		Installing forward Aerosport Interior Side Panels.	16/1/2020	5.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS / ENHANCEMENTS	INTERIOR LIGHTS	A friend 3d printed a bracket to hold to mount the compass. Tailcon lighitng with 2 small individual LEDs installed.	16/1/2020	2.25	Halanda	Benedikovic
ENHANCEMENTS	SUN SHIELDS	http://www.aviatorshop.eu/RV-10/2020/04/30/2012020-sun-shields/	20/1/2020	2.75	Halanda	Benedikovic
INVENTORY		ANDAIR CHECK VALVES for fuel tank breathers ANDAIR DV125 Drain Valves for fuel tanks to replace original Vans drain valves.	21/1/2020	0.1	Halanda
PAINT / FURNISHING / UPHOLSTERY		Trimming and attaching the rear Aerosport interior panels.	22/1/2020	6	Halanda	Benedikovic
ELECTRICAL & AVIONICS	MISC	Installing the doors closed limit switches. Panasonic AZ7120CE	26/1/2020	4.75	Halanda	Benedikovic
ENHANCEMENTS / FUSELAGE KIT	38 Rudder Pedals & Brake System / BERINGER Brakes & Parking Brake	Filling the BERINGER brake system with RADCOLUB FR257 (MIL-PRF-87257) fluid. +looking for potential leaks -found 3	28/1/2020	2.5	Halanda	Benedikovic
FUSELAGE KIT	43 CABIN TOP	Filler and sanding the front A pillars on cabin top to accommodate the front Aerosport side panels.	31/1/2020	4.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Last trimming and attaching the forward Aerosport Interior Panels.	2/2/2020	2.75	Halanda	Benedikovic
ENHANCEMENTS	INTERIOR LIGHTS	Wheelen LED - Baggage Light -test performed	3/2/2020	0.25	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Wet Compass blind riveted to the Center Cabin Brace (WD-1043)	6/2/2020	0.5	Halanda	Benedikovic
INVENTORY		AMPLOC Hall Effect Current Sensors Headrests for rear seats	7/2/2020	0.25	Halanda
ENHANCEMENTS	MISC	Forward Harness Holder Brackets. These are being designed to hold the forward shoulder harnesses on top when not in use.	11/2/2020	2.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Michal, (the upholstery specialist) is working on the forward seats.	15/2/2020
ELECTRICAL & AVIONICS	MISC	Fabricating a removable contactor bracket for 2 contactors in the tailcone section.	15/2/2020	3.1	Halanda	Benedikovic
ELECTRICAL & AVIONICS	INSTRUMENT PANEL	Relabeled the BACKUP switch into ESS to make it more obvious for pilots that this switch feeds the ESSENTIAL BUS and its components. So far, 3D model only.	16/2/2020	0.5	Halanda
PAINT / FURNISHING / UPHOLSTERY		Headrests for rear pax installed	19/2/2020	2.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Interior Paint	3/3/2020	5	Halanda	Benedikovic
INVENTORY		STATIC WICKS DD-1W with B-4 BASE	4/3/2020	0.1	Halanda
PAINT / FURNISHING / UPHOLSTERY ENHANCEMENTS	PLANEAROUND DOOR LOCKING SYSTEM	Installing Door Sills from Aerosport and PlaneAround central door locking safety mecanism.	4/3/2020	4.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Forward Seats Progress -Ready for testing..	13/3/2020
PAINT / FURNISHING / UPHOLSTERY		Fwd Gear Fork anodized	15/3/2020	2	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Door Paint -Found some spots that had to be redone.	16/3/2020	3.75	Halanda	Benedikovic
INVENTORY		FWFD KIT Inventory + Engine and Prop	20/3/2020	6.25	Halanda	Benedikovic
INVENTORY		GIGAVAC Contactors GX11SA	25/3/2020	0.1	Halanda	Benedikovic
FIREWALL FORWARD	FF1-5 ENGINE INSTALLATION	Installing the IO540	26/3/2020	2.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Testing the seat foams	26/3/2020	0.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Interior Paint (doors)	28/3/2020	2	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	(47) SPINNER & COWLING	29/3/2020	4.5	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	(47) SPINNER & COWLING	30/3/2020	4	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling	31/3/2020	6.5	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling Modification on the bottom cowls -will use two fasteners per side.	1/4/2020	2	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling	2/4/2020	6.5	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling	3/4/2020	3.5	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling	4/4/2020	4	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling +starter removal for SALE! (sold)	5/4/2020	3.75	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling Louvers were alodined.	8/4/2020	5.75	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling	10/4/2020	3.5	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	FF2-1 -> FF2-20 Starting works on the baffles.	11/4/2020	2.1	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	FF2-1 -> FF2-20	12/4/2020	3.5	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	FF2-1 -> FF2-20	13/4/2020	5.25	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	FF2-1 -> FF2-20	14/4/2020	4.5	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	FF2-1 -> FF2-20	15/4/2020	3.75	Halanda	Benedikovic
INVENTORY		Flap handle came back from friend’s dad who made this perfect label on the handle to identify the switch function. I’ll put some clear coat on to protect the text.. Thank you Rastik! 😉	15/4/2020	0.1	Halanda		FLAP HANDLE RECEIVED LABELED
FIREWALL FORWARD	FF2 COWLE BAFFLE	FF2-1 -> FF2-20 + left magneto removed FOR SALE!	18/4/2020	3.5	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	FF2-1 -> FF2-20 Trimming horizontal pins and various adjustments..	19/4/2020	4.75	Halanda	Benedikovic
FIREWALL FORWARD	FF4 FUEL SYSTEM & FAB 540 AP	FAB (AIR BOX)	22/4/2020	2.5	Halanda	Benedikovic
FIREWALL FORWARD	FF4 FUEL SYSTEM & FAB 540 AP	FAB (AIR BOX)	23/4/2020	3	Halanda	Benedikovic
INVENTORY		AIR AVIONICS AT1 & SEAT LEATHER	24/4/2020	0.2	Halanda		AIR AVIONICS AT1 & SEAT LEATHER
FIREWALL FORWARD	FF4 FUEL SYSTEM & FAB 540 AP	FAB (AIR BOX)	24/4/2020	2.75	Halanda	Benedikovic
FIREWALL FORWARD	FF4 FUEL SYSTEM & FAB 540 AP	FAB (AIR BOX) & Air Inlet	25/4/2020	1.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	MISC	CONTACTORS INSTALLATION	25/4/2020	2.5	Halanda	Benedikovic
FIREWALL FORWARD	FF4 FUEL SYSTEM & FAB 540 AP	Air Inlet in the cowling:	26/4/2020	1.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		HARNESS COLOR: Looking for the right belts and harnesses color to complement the cockpit interior color.	27/4/2020	0.5	Halanda
ELECTRICAL & AVIONICS	220V OIL PREHEAT SYSTEM	Installing the low profile IP65 rated 220V socket for the EZ-HEAT oil preheat system. Plug and socket feature a lockable system which can be connected and disconnect hot / under load.	28/4/2020	0.5	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	AIR SEAL FABRIC	29/4/2020	3.75	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	Screw fasteners instead of bottom cowl hinges. This mod will make removing and attaching the bottom cowl easier. +1 shot behind the bulkhead..	30/4/2020	1.5	Halanda	Benedikovic
FINISH KIT	47 SPINNER & COWLING	47-4->47-12 Cowling +poor man’s ‘LightBox’	30/4/2020	0.75	Halanda	Benedikovic
ENHANCEMENTS	ANDAIR Oil Separator	Position of the collector has changed for better access. Custom hoses added -might need to modify later with second alternator and oil filter adapter installed.	4/5/2020	4.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Valve Covers Paint Removal	6/5/2020	1	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY	FF2 COWLE BAFFLE	Baffles alodined and Valve Covers Chrome-plated	7/5/2020	4.75	Halanda	Benedikovic
FIREWALL FORWARD	FF4 FUEL SYSTEM & FAB 540 AP	Aluminium plated fixated below the air filter to avoid the air filter rubbing through the air box.	9/5/2020	1.25	Halanda	Benedikovic
FIREWALL FORWARD	FF4 FUEL SYSTEM & FAB 540 AP	FAB modified to use an Automatic Alternate Air Door sytem. No pilot action required.	13/5/2020	1.75	Halanda	Benedikovic
FIREWALL FORWARD	FF2 COWLE BAFFLE	(FF2-17) Tensions springs instead of tension rods. This section has been modified to use tension springs instead of tension rods. For easy of operation/removal/installation.	13/5/2020	2.25	Halanda	Benedikovic
FIREWALL FORWARD	FF3 CONTROL CABLES	FF3 Installing Push/Pull Control Cables	13/5/2020	1.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	MISC	New Contactor Holder Bracket	16/5/2020	2.75	Halanda	Benedikovic
FIREWALL FORWARD / ELECTRICAL & AVIONICS	FF5 OIL SYSTEM ELECTRICAL & AVIONICS	B&C Oil Filter Adapter, Starter & Alternators	21/5/2020	2.25	Halanda	Benedikovic
ELECTRICAL & AVIONICS	SUREFLY Electronic Magneto	SUREFLY Electronic Magneto	22/5/2020	1.25	Halanda	Benedikovic
FIREWALL FORWARD	FF4 FUEL SYSTEM, FF5 OIL SYSTEM	Oil & Fuel Hoses	22/5/2020	2.75	Halanda	Benedikovic
ELECTRICAL & AVIONICS	External Power Connector, Antennas	Flarm Antenna, EXT PWR CB installed	25/5/2020	2	Halanda	Benedikovic
FIREWALL FORWARD	FF6 EXHAUST SYSTEM, ELECTRICAL & AVIONICS	Spark Plugs Wiring & Exhaust installed	28/5/2020	2.5	Halanda	Benedikovic
FIREWALL FORWARD	47 SPINNER & COWLING	Cowling	29/5/2020	4	Halanda	Benedikovic
FIREWALL FORWARD	47 SPINNER & COWLING	COWLING	30/5/2020	3.5	Halanda	Benedikovic
FIREWALL FORWARD	FF1 ENGINE INSTALLATION	PROP GOVERNOR INSTALLATION	6/6/2020	2.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	220V OIL PREHEAT SYSTEM	E-Z Heat Preheat Pads	7/6/2020	3.75	Halanda	Benedikovic
FIREWALL FORWARD	FF3 CCONTROL CABLES	Control Cables installation	8/6/2020	5.75	Halanda	Benedikovic
FIREWALL FORWARD	47 SPINNER & COWLING	Cowling	9/6/2020	4.5	Halanda	Benedikovic
FIREWALL FORWARD	FF6 EXHAUST SYSTEM	FF6 EXHAUST SYSTEM	10/6/2020	3.75	Halanda	Benedikovic
FIREWALL FORWARD	FF3 CCONTROL CABLES	FF3 Control Cables	10/6/2020	3	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Artex 345 ELT installation	11/6/2020	2.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Front Seats Upholstery in progress	12/6/2020
FIREWALL FORWARD	47 SPINNER & COWLING	COWLING	13/6/2020	4	Halanda	Benedikovic
WINGS KIT	24 WING TIP	Wingtip Light Lense	15/6/2020	3	Halanda	Benedikovic
FIREWALL FORWARD	47 SPINNER & COWLING	COWLING	16/6/2020	4	Halanda	Benedikovic
INVENTORY		INVENTORY Pins & CO Detector	25/6/2020	0.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Front Seats: lower part finished	26/6/2020
ELECTRICAL & AVIONICS		Defog Fans	27/6/2020	1.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Front Seats: Headset Hangers	28/6/2020	2	Halanda	Benedikovic
Overhead Console / System		Overhead panel	28/6/2020	4.25	Halanda	Benedikovic
FINISH KIT	49 SEATS & SEAT BELTS	Front Seat Rails	29/6/2020	1.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Headset Hangers & Aerosport Seat Handle	29/6/2020	4	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Installing AT-1 Traffic & both Regulators	3/7/2020	1.5	Halanda	Benedikovic
INVENTORY		INVENTORY: G5 GPS Antenna, Coup holders for rear seats, Magneto RPM sensor, Updated 75PSI Fuel Pressure Transducer	11/7/2020	0.25	Halanda	Benedikovic
Overhead Console / System, Interior Lights		Overhead Panel lights	20/7/2020	3	Halanda	Benedikovic
FIREWALL FORWARD ELECTRICAL & AVIONICS	FF4 FUEL SYSTEM	Engine Sensors: FT-60 (RED BOX) Fuel Flow Metering Unit, Fuel Press. Sensor, MAP Sensor, Oil Press Sensor	26/7/2020	4.75	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Trim Motors Wiring: Using DTM connectors.	31/7/2020	2.75	Loy	Benedikovic
ELECTRICAL & AVIONICS		Static Wicks installation & Ground Points	5/8/2020	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Antennas	AT-1 Firewall Antenna PassThrough	7/8/2020	1	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel MockUp: For Avionics Installation..	9/8/2020	5.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Trim Motors/Servos wiring: DTM connectors in use.	10/8/2020	1.5	Loy	Benedikovic
INVENTORY		INVENTORY Avionics	14/8/2020	1	Halanda	Benedikovic
ELECTRICAL & AVIONICS, PITOT STATIC SYSTEM	Instrument Panel	Air Connection to and via GSU25: AOA, Static and Total Pressure lines	29/8/2020	2	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Key Switch Installation	31/8/2020	0.25	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Wiring & Electrical	5/9/2020	4.5	Loy	Benedikovic
ELECTRICAL & AVIONICS	Antennas	Electrical & Wiring (Antennas)	6/9/2020	8	Loy	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Front Seats Upholstery: Front Seats Upholstery finished.	10/9/2020		Halanda	Benedikovic
SERVICE BULLETINS		Service Bulletin SB 18-03-30	14/9/2020	4	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Helping hands by Barbora -student from Faculty of Aeronautics	18/9/2020	5	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Avionics Installation / Wiring	19/9/2020	8	Loy	Benedikovic
ELECTRICAL & AVIONICS		Avionics Installation / Wiring	27/9/2020	8.5	Loy	Benedikovic
ELECTRICAL & AVIONICS		Avionics Installation / Wiring	7/10/2020	8	Loy	Benedikovic
ELECTRICAL & AVIONICS		Avionics Installation / Wiring	10/10/2020	7.5	Loy	Benedikovic
ELECTRICAL & AVIONICS		Avionics Installation / Wiring	14/10/2020	8	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel Inserts	15/10/2020	3	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel Inserts	21/10/2020	8	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel Inserts	25/10/2020	8	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Avionics Installation / Wiring: DME connector KN63 and Alternator Connector replacement	6/11/2020	2	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel	11/11/2020	9	Halanda	Benedikovic
MISC		Covers & Plugs arrived	20/11/2020	0.25	Halanda	Benedikovic
ELECTRICAL & AVIONICS		DME KN63 Connector Wiring	5/12/2020	0.75	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel Inserts	7/12/2020	8	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Electrical / Wiring / Avionics	9/12/2020	8	Loy	Benedikovic
FIREWALL FORWARD	FF6 EXHAUST SYSTEM	FF6-4 EXHAUST SYSTEM: Heating /Vent Scat	9/12/2020	1	Halanda	Benedikovic
ENHANCEMENTS	220V OIL PREHEAT SYSTEM	Oil Preheat System / Plug Cover: Designing the PreHeat Plug Cover	13/12/2020	4.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS		GMU11 MagnetoMeter Bracket	14/12/2020	2.75	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Starter Engaged Warning Relay: Mounted on the firewall.	15/12/2020	2.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Electrical / Wiring / Avionics	18/12/2020	6	Loy	Benedikovic
ENHANCEMENTS	PlaneAround Door Locking System	Planearound Door Locking System	31/12/2020	4.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Electrical / Wiring / Avionics: Rocker Switches backlight wiring..	11/1/2021	5.75	Loy	Benedikovic
ELECTRICAL & AVIONICS		OAT probe and Stall Warn installation	12/1/2021	2.75	Loy	Benedikovic
ELECTRICAL & AVIONICS		Electrical / Wiring: Circuit Breaker Panel	20/1/2021	7.75	Loy, Halanda	Benedikovic
ELECTRICAL & AVIONICS		Electrical / Wiring: Flap Position Sensor, Ground Termination/Junction Boxes..	27/1/2021	8	Loy	Benedikovic
ELECTRICAL & AVIONICS	External Power Connector	Electrical / Wiring: Wing root holes for connectors; Alternator 1 and Starter Wiring; Preheat System plug cover, Rudder Trim Switch wiring; Fuel Sensor Wiring, MASTER and ESS switches	31/1/2021	7.5	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Electrical / Wiring: Annunciator Test Switch; Instrument Mockup Panel	6/2/2021	6.75	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Electrical / Wiring Avionics: Wiring with predetermined wire lengths:	10/2/2021	8.5	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Electrical / Wiring: Audio Wires; Avionics Wiring	20/2/2021	9	Loy	Benedikovic
ELECTRICAL & AVIONICS	Interior Lights	Dome Light Timer: Dome Light Timer prototype	9/3/2021	3	Loy	Benedikovic
ELECTRICAL & AVIONICS	220V OIL PREHEAT SYSTEM	Electrical / Wiring: Prewired cables go behind the panel.. Diode block; Wing Root Wiring; Amplock AMP meter	10/3/2021	7.5	Loy	Benedikovic
ELECTRICAL & AVIONICS		Grip Wiring	17/3/2021	6	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel Wiring	25/3/2021	6.5	Loy	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Initial Avionics Startup: Initial Avionics startup. No faults	26/3/2021	1	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Avionics Setup: Setting up the sensors and limitations..	30/3/2021	4	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Database Updates	3/4/2021	3	Halanda	Benedikovic
Workshop, Transports		Trial Move out of the Workshop	3/4/2021	0.5		Benedikovic
ELECTRICAL & AVIONICS		Avionics Setup / Configuration: Audio Panel does not respond when configured to correct GMA345 model..	6/4/2021	4.5	Halanda	Benedikovic
SERVICE BULLETINS		Service Bulletin SB-00002	12/4/2021	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Avionics / Wiring	14/4/2021	8.75	Loy	Benedikovic
ELECTRICAL & AVIONICS	Antennas	COM 2 Antenna	14/4/2021	1.5	Loy	Benedikovic
ELECTRICAL & AVIONICS		Avionics Configuration	16/4/2021	6	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Inventory: GNC 255 Backplate and DTM Connector	20/4/2021	1	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Rear Seat Base Plate Construction	24/4/2021	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Avionics / Wiring: Tailcone Wiring	29/4/2021	3.75	Loy	Benedikovic
FAB 540 AP, ENHANCEMENTS		Update of the Automatic Alternate Door	29/4/2021	2	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	COM / NAV 2 Installation & Wiring Check	29/4/2021	3	Loy	Benedikovic
ELECTRICAL & AVIONICS, Workshop, Transports, 44 Wing Attachement		Moving to the hangar & Wings installation: Electrical / Avionics Guru/Maestro Jaro Loy on picture.	29/4/2021	1
ELECTRICAL & AVIONICS	Exterior Lights	Landing Light & Pos. Lts Test	30/4/2021	0.5	Loy	Benedikovic
ENHANCEMENTS	Center Console, ANDAIR Fuel System	Center Console with Fuel Selector	1/5/2021	2	Halanda	Benedikovic
ENHANCEMENTS	ANDAIR Fuel System	Fuel Tank Alternate Air Valve: Check Valve from Andair installed. Opens automatically when the fuel intace becomes blocked to prevent fuel tank collapse.	1/5/2021	1.5	Halanda	Benedikovic
EMPENNAGE KIT	9 Elevators	Elevator Installation	3/5/2021	1.75	Halanda	Benedikovic
BUILDER'S LOGBOOK		CAA Visit	4/5/2021
ELECTRICAL & AVIONICS	Instrument Panel	Instrument Panel Inserts: Custom made insert with description (Left Panel)	5/5/2021
EMPENNAGE KIT	7 Rudder, 12 Empenage Fairings	Rudder & Empenage Fairings	6/5/2021	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS FIREWALL, FORWARD, FINISH KIT	27 Firewall, Instrument Panel, 50 Cabin Heat & Ventilation, FF5 OIL SYSTEM	Push&Pull Controls final installation: Rear Heat, Front Heat, Parking Brake, Oil Cooler Door	12/5/2021	3	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Wiring Tailcone & Overhead Panel	14/5/2021	6	Loy	Benedikovic
FUSELAGE KIT	43 Cabin Cover	Tailcone Fwd Top Skin	16/5/2021	3.5	Halanda	Benedikovic
WINGS KIT	22 Flaps	Flaps Install	18/5/2021	4	Halanda	Benedikovic
FUSELAGE KIT	35 Access Covers and Floor Panels	35-9 Mid Cabin Side Covers	21/5/2021	2.25	Halanda	Benedikovic
		First Refueling: Preparation for initial engine start.	29/5/2021	0.5	Halanda	Benedikovic
		1st Engine Start: Maestro himself before we pulled the RV-10 out of the hangar for the 1st engine start:	30/5/2021	2	Halanda	Benedikovic
ENHANCEMENTS, WINGS KIT	18 Fuel Tank, ANDAIR Fuel System	Fuel Breather Line	1/6/2021	2	Halanda	Benedikovic
ENHANCEMENTS, PAINT / FURNISHING / UPHOLSTERY	Center Console	Armrest Installation	2/6/2021	0.25	Halanda	Benedikovic
FINAL PREPARATIONS		Covers & Final Exterior Scan	5/6/2021	0.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Rear Seat Bank finished	9/6/2021
ENHANCEMENTS		Panel Inserts & Decals: Graphics & Final Products..	10/6/2021	5.75	Halanda	Benedikovic
FINAL PREPARATIONS		Flight Controls Lock: Initial design seems to work well except ailerons / flaps lock. We run into the danger of damage when selecting flaps above 15deg with the lock installed. Ailerons + Wing Tip makes more sense but the discharger is in the way – we will think it over.. Rudder & Elevator lock works very well.	11/6/2021	5.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	G5 Static+Total Pressure Connections: Instrument Panel almost finished	12/6/2021	7.75	Halanda	Benedikovic
Welcome		Sun Shades: Sun Shades installed.	18/6/2021	3	Halanda	Benedikovic
FINAL PREPARATIONS		Initial Weighting: still paintless..	24/6/2021	3	Halanda	Benedikovic
INVENTORY		Rudder Trim Springs Inventory	24/6/2021	0.5	Halanda
PAINT / FURNISHING / UPHOLSTERY		Rear Seat installed & brought to trial	4/7/2021	1	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	Com / Nav 2 installed: GNC255	3/8/2021	0.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS / FUSELAGE KIT	Instrument Panel, 39 Control System	Grip Sticks installed	25/8/2021	3.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS	Instrument Panel	SMART GLIDE push button: Optional SMART GLIDE momentary push button.	16/9/2021	1	Halanda
ELECTRICAL & AVIONICS	Instrument Panel	Right Instrument Panel with Labels installed	9/9/2021	2.5	Halanda	Benedikovic
ELECTRICAL & AVIONICS		Roll Servo has failed. Pulled out for replacement..	2/10/2021	0.75	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Front Seat Belts & Shoulder Harness	2/10/2021	1.25	Halanda	Benedikovic
Misc		Interior Door Handle	3/10/2021	1	Halanda	Benedikovic
PITOT STATIC SYSTEM		Pitot Static Leak Test	4/10/2021	2.5		Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Rear Headrests installed	6/10/2021	0.5	Halanda	Benedikovic
PAINT / FURNISHING / UPHOLSTERY		Glareshield Edge Protection extended	3/11/2021	0.25	Halanda	Benedikovic
Antennas		Antennas check	10/11/2021	3.75	Halanda	Benedikovic
Welcome		SPECIAL AIRWORTHINESS CERTIFICATE issued	18/11/2021

OM-ELA (Van's RV-10 builder's log)

(stavebný denník lietadla Van's RV-10 S/N 41519)

7 Rudder

6.5.2021 Rudder & Empenage Fairings

Rudder: FINISHED

Rudder: progress picture

Rudder: started works today

BUILDER'S LOGBOOK (S/N 41519)

November 2024
M	T	W	T	F	S	S
« Dec
				1	2	3
4	5	6	7	8	9	10
11	12	13	14	15	16	17
18	19	20	21	22	23	24
25	26	27	28	29	30